| /nrf52832-nimble/packages/NimBLE-latest/nimble/host/src/ |
| H A D | ble_l2cap_coc.c | 203 /* Lets get back control to os_mbuf to application. in ble_l2cap_coc_rx_fn()
217 * However, we still have buffer to for next LE Frame so lets give one more in ble_l2cap_coc_rx_fn()
221 /* Remote did not send full SDU. Lets give him one more credits to do in ble_l2cap_coc_rx_fn()
338 /* lets calculate data we are going to send */ in ble_l2cap_coc_continue_tx()
|
| H A D | ble_l2cap_sig.c | 625 * event with error status. To avoid additional disconnected event lets in ble_l2cap_sig_coc_connect_cb()
979 /* This response is incorrect, lets wait for timeout */ in ble_l2cap_sig_disc_rsp_rx()
|
| /nrf52832-nimble/packages/NimBLE-latest/nimble/controller/src/ |
| H A D | ble_ll_scan.c | 974 * If device matches, lets check for InitA further in the code in ble_ll_scan_chk_filter_policy()
1158 /* Well, in case we missed to schedule scan, lets move to next stan interval. in ble_ll_scan_get_current_scan_win()
1401 /* Lets check if we want to switch to other PHY */ in ble_ll_scan_start_next_phy()
1501 /* In case continous scan lets assume we area always in the window*/ in ble_ll_scan_event_proc()
1844 /* Lets reuse old aux_data */ in ble_ll_scan_get_aux_data()
2092 /* If this is just becon with no aux data, lets get address from the packet */ in ble_ll_scan_get_addr_from_ext_adv()
2290 /* Lets get addresses from advertising report*/ in ble_ll_scan_rx_isr_end()
2331 * lets do a copy of pointers for scan request in ble_ll_scan_rx_isr_end()
2429 /* On handover lets increase ref count */ in ble_ll_scan_rx_isr_end()
2855 /* For the time when sending events up, lets increase ref count */ in ble_ll_scan_rx_pkt_in()
|
| H A D | ble_ll_conn.c | 3059 /* Lets take last used phy */ in ble_ll_init_rx_pkt_in()
3274 /* Lets get addresses from advertising report*/ in ble_ll_init_rx_isr_end()
3293 /* If this is not connectable adv mode, lets skip it */ in ble_ll_init_rx_isr_end()
3306 /* if there is direct address lets fall down and check it.*/ in ble_ll_init_rx_isr_end()
3387 /* Lets make sure privacy mode is correct together with InitA in case it in ble_ll_init_rx_isr_end()
3469 /* Lets wait for AUX_CONNECT_RSP */ in ble_ll_init_rx_isr_end()
|
| H A D | ble_ll_sched.c | 1341 /* Lets calculate roughly how much time we need for scan req and scan rsp */ in ble_ll_sched_scan_req_over_aux_ptr()
|
| /nrf52832-nimble/rt-thread/examples/network/ |
| H A D | chargen.c | 94 /* Lets create a new control block */ in chargen_thread()
|
| /nrf52832-nimble/packages/NimBLE-latest/nimble/host/test/src/ |
| H A D | ble_l2cap_test.c | 805 /* Lets check if there is accept event */ in ble_l2cap_test_coc_connect_by_peer()
882 * lets reuse it */ in ble_l2cap_test_coc_disc_by_peer()
919 * and checks the type of the event, lets increase event counter here and in ble_l2cap_test_coc_send_data()
|
| /nrf52832-nimble/packages/NimBLE-latest/nimble/host/mesh/ |
| H A D | syscfg.yml | 423 Procedure and lets the state be changed at any time.
|
| /nrf52832-nimble/rt-thread/components/dfs/filesystems/nfs/rpc/ |
| H A D | xdr.h | 127 /* lets you reposition the stream */
|
| /nrf52832-nimble/rt-thread/tools/kconfig-frontends/frontends/mconf/ |
| H A D | mconf.c | 28 "This interface lets you select features and parameters for the build.\n"
|
| /nrf52832-nimble/rt-thread/tools/kconfig-frontends/frontends/nconf/ |
| H A D | nconf.c | 32 "This interface lets you select features and parameters for the kernel\n"
|
| /nrf52832-nimble/rt-thread/components/net/uip/doc/ |
| H A D | uip-doc.txt | 282 application may be able to regenerate sent data and lets the
|
| /nrf52832-nimble/rt-thread/components/net/lwip-1.4.1/src/api/ |
| H A D | api_msg.c | 880 /* @todo: this lets select make the socket readable and writable,
|
| /nrf52832-nimble/rt-thread/components/net/lwip-2.0.2/src/api/ |
| H A D | api_msg.c | 1097 /* @todo: this lets select make the socket readable and writable,
|
| /nrf52832-nimble/rt-thread/components/net/uip/doc/html/ |
| H A D | main.html | 68 …zes the fact that the application may be able to regenerate sent data and lets the application tak…
|
| /nrf52832-nimble/rt-thread/components/net/lwip-2.1.0/src/api/ |
| H A D | api_msg.c | 1198 /* @todo: this lets select make the socket readable and writable,
|
| /nrf52832-nimble/rt-thread/components/net/lwip-2.0.2/src/include/lwip/ |
| H A D | opt.h | 186 * this lets tcpip_input() grab the mutex for input packets as well,
|
| /nrf52832-nimble/rt-thread/components/net/lwip-2.1.0/src/include/lwip/ |
| H A D | opt.h | 195 * this lets tcpip_input() grab the mutex for input packets as well,
|
| /nrf52832-nimble/rt-thread/tools/kconfig-frontends/scripts/.autostuff/m4/ |
| H A D | libtool.m4 | 1743 # nice to cause kernel panics so lets avoid the loop below.
|
| /nrf52832-nimble/rt-thread/tools/kconfig-frontends/ |
| H A D | configure | 5331 # nice to cause kernel panics so lets avoid the loop below.
|