1 /** 2 ****************************************************************************** 3 * @file stm32f4xx_hal_conf.h 4 * @brief HAL configuration file. 5 ****************************************************************************** 6 * @attention 7 * 8 * <h2><center>© COPYRIGHT(c) 2019 STMicroelectronics</center></h2> 9 * 10 * Redistribution and use in source and binary forms, with or without modification, 11 * are permitted provided that the following conditions are met: 12 * 1. Redistributions of source code must retain the above copyright notice, 13 * this list of conditions and the following disclaimer. 14 * 2. Redistributions in binary form must reproduce the above copyright notice, 15 * this list of conditions and the following disclaimer in the documentation 16 * and/or other materials provided with the distribution. 17 * 3. Neither the name of STMicroelectronics nor the names of its contributors 18 * may be used to endorse or promote products derived from this software 19 * without specific prior written permission. 20 * 21 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 22 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 23 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE 24 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE 25 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 26 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR 27 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER 28 * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, 29 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE 30 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 31 * 32 ****************************************************************************** 33 */ 34 35 /* Define to prevent recursive inclusion -------------------------------------*/ 36 #ifndef __STM32F4xx_HAL_CONF_H 37 #define __STM32F4xx_HAL_CONF_H 38 39 #ifdef __cplusplus 40 extern "C" { 41 #endif 42 43 /* Exported types ------------------------------------------------------------*/ 44 /* Exported constants --------------------------------------------------------*/ 45 46 /* ########################## Module Selection ############################## */ 47 /** 48 * @brief This is the list of modules to be used in the HAL driver 49 */ 50 #define HAL_MODULE_ENABLED 51 52 /* #define HAL_ADC_MODULE_ENABLED */ 53 /* #define HAL_CRYP_MODULE_ENABLED */ 54 /* #define HAL_CAN_MODULE_ENABLED */ 55 /* #define HAL_CRC_MODULE_ENABLED */ 56 /* #define HAL_CRYP_MODULE_ENABLED */ 57 /* #define HAL_DAC_MODULE_ENABLED */ 58 /* #define HAL_DCMI_MODULE_ENABLED */ 59 /* #define HAL_DMA2D_MODULE_ENABLED */ 60 /* #define HAL_ETH_MODULE_ENABLED */ 61 /* #define HAL_NAND_MODULE_ENABLED */ 62 /* #define HAL_NOR_MODULE_ENABLED */ 63 /* #define HAL_PCCARD_MODULE_ENABLED */ 64 /* #define HAL_SRAM_MODULE_ENABLED */ 65 /* #define HAL_SDRAM_MODULE_ENABLED */ 66 /* #define HAL_HASH_MODULE_ENABLED */ 67 #define HAL_I2C_MODULE_ENABLED 68 #define HAL_I2S_MODULE_ENABLED 69 /* #define HAL_IWDG_MODULE_ENABLED */ 70 /* #define HAL_LTDC_MODULE_ENABLED */ 71 /* #define HAL_RNG_MODULE_ENABLED */ 72 /* #define HAL_RTC_MODULE_ENABLED */ 73 /* #define HAL_SAI_MODULE_ENABLED */ 74 /* #define HAL_SD_MODULE_ENABLED */ 75 /* #define HAL_MMC_MODULE_ENABLED */ 76 #define HAL_SPI_MODULE_ENABLED 77 /* #define HAL_TIM_MODULE_ENABLED */ 78 #define HAL_UART_MODULE_ENABLED 79 /* #define HAL_USART_MODULE_ENABLED */ 80 /* #define HAL_IRDA_MODULE_ENABLED */ 81 /* #define HAL_SMARTCARD_MODULE_ENABLED */ 82 /* #define HAL_WWDG_MODULE_ENABLED */ 83 /* #define HAL_PCD_MODULE_ENABLED */ 84 /* #define HAL_HCD_MODULE_ENABLED */ 85 /* #define HAL_DSI_MODULE_ENABLED */ 86 /* #define HAL_QSPI_MODULE_ENABLED */ 87 /* #define HAL_QSPI_MODULE_ENABLED */ 88 /* #define HAL_CEC_MODULE_ENABLED */ 89 /* #define HAL_FMPI2C_MODULE_ENABLED */ 90 /* #define HAL_SPDIFRX_MODULE_ENABLED */ 91 /* #define HAL_DFSDM_MODULE_ENABLED */ 92 /* #define HAL_LPTIM_MODULE_ENABLED */ 93 /* #define HAL_EXTI_MODULE_ENABLED */ 94 #define HAL_GPIO_MODULE_ENABLED 95 #define HAL_EXTI_MODULE_ENABLED 96 #define HAL_DMA_MODULE_ENABLED 97 #define HAL_RCC_MODULE_ENABLED 98 #define HAL_FLASH_MODULE_ENABLED 99 #define HAL_PWR_MODULE_ENABLED 100 #define HAL_CORTEX_MODULE_ENABLED 101 102 /* ########################## HSE/HSI Values adaptation ##################### */ 103 /** 104 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. 105 * This value is used by the RCC HAL module to compute the system frequency 106 * (when HSE is used as system clock source, directly or through the PLL). 107 */ 108 #if !defined (HSE_VALUE) 109 #define HSE_VALUE ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */ 110 #endif /* HSE_VALUE */ 111 112 #if !defined (HSE_STARTUP_TIMEOUT) 113 #define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */ 114 #endif /* HSE_STARTUP_TIMEOUT */ 115 116 /** 117 * @brief Internal High Speed oscillator (HSI) value. 118 * This value is used by the RCC HAL module to compute the system frequency 119 * (when HSI is used as system clock source, directly or through the PLL). 120 */ 121 #if !defined (HSI_VALUE) 122 #define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/ 123 #endif /* HSI_VALUE */ 124 125 /** 126 * @brief Internal Low Speed oscillator (LSI) value. 127 */ 128 #if !defined (LSI_VALUE) 129 #define LSI_VALUE ((uint32_t)32000U) /*!< LSI Typical Value in Hz*/ 130 #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz 131 The real value may vary depending on the variations 132 in voltage and temperature.*/ 133 /** 134 * @brief External Low Speed oscillator (LSE) value. 135 */ 136 #if !defined (LSE_VALUE) 137 #define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External Low Speed oscillator in Hz */ 138 #endif /* LSE_VALUE */ 139 140 #if !defined (LSE_STARTUP_TIMEOUT) 141 #define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */ 142 #endif /* LSE_STARTUP_TIMEOUT */ 143 144 /** 145 * @brief External clock source for I2S peripheral 146 * This value is used by the I2S HAL module to compute the I2S clock source 147 * frequency, this source is inserted directly through I2S_CKIN pad. 148 */ 149 #if !defined (EXTERNAL_CLOCK_VALUE) 150 #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the External audio frequency in Hz*/ 151 #endif /* EXTERNAL_CLOCK_VALUE */ 152 153 /* Tip: To avoid modifying this file each time you need to use different HSE, 154 === you can define the HSE value in your toolchain compiler preprocessor. */ 155 156 /* ########################### System Configuration ######################### */ 157 /** 158 * @brief This is the HAL system configuration section 159 */ 160 #define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */ 161 #define TICK_INT_PRIORITY ((uint32_t)0U) /*!< tick interrupt priority */ 162 #define USE_RTOS 0U 163 #define PREFETCH_ENABLE 1U 164 #define INSTRUCTION_CACHE_ENABLE 1U 165 #define DATA_CACHE_ENABLE 1U 166 167 /* ########################## Assert Selection ############################## */ 168 /** 169 * @brief Uncomment the line below to expanse the "assert_param" macro in the 170 * HAL drivers code 171 */ 172 /* #define USE_FULL_ASSERT 1U */ 173 174 /* ################## Ethernet peripheral configuration ##################### */ 175 176 /* Section 1 : Ethernet peripheral configuration */ 177 178 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ 179 #define MAC_ADDR0 2U 180 #define MAC_ADDR1 0U 181 #define MAC_ADDR2 0U 182 #define MAC_ADDR3 0U 183 #define MAC_ADDR4 0U 184 #define MAC_ADDR5 0U 185 186 /* Definition of the Ethernet driver buffers size and count */ 187 #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ 188 #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ 189 #define ETH_RXBUFNB ((uint32_t)4U) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ 190 #define ETH_TXBUFNB ((uint32_t)4U) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ 191 192 /* Section 2: PHY configuration section */ 193 194 /* DP83848_PHY_ADDRESS Address*/ 195 #define DP83848_PHY_ADDRESS 0x01U 196 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ 197 #define PHY_RESET_DELAY ((uint32_t)0x000000FFU) 198 /* PHY Configuration delay */ 199 #define PHY_CONFIG_DELAY ((uint32_t)0x00000FFFU) 200 201 #define PHY_READ_TO ((uint32_t)0x0000FFFFU) 202 #define PHY_WRITE_TO ((uint32_t)0x0000FFFFU) 203 204 /* Section 3: Common PHY Registers */ 205 206 #define PHY_BCR ((uint16_t)0x0000U) /*!< Transceiver Basic Control Register */ 207 #define PHY_BSR ((uint16_t)0x0001U) /*!< Transceiver Basic Status Register */ 208 209 #define PHY_RESET ((uint16_t)0x8000U) /*!< PHY Reset */ 210 #define PHY_LOOPBACK ((uint16_t)0x4000U) /*!< Select loop-back mode */ 211 #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100U) /*!< Set the full-duplex mode at 100 Mb/s */ 212 #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000U) /*!< Set the half-duplex mode at 100 Mb/s */ 213 #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100U) /*!< Set the full-duplex mode at 10 Mb/s */ 214 #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000U) /*!< Set the half-duplex mode at 10 Mb/s */ 215 #define PHY_AUTONEGOTIATION ((uint16_t)0x1000U) /*!< Enable auto-negotiation function */ 216 #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200U) /*!< Restart auto-negotiation function */ 217 #define PHY_POWERDOWN ((uint16_t)0x0800U) /*!< Select the power down mode */ 218 #define PHY_ISOLATE ((uint16_t)0x0400U) /*!< Isolate PHY from MII */ 219 220 #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020U) /*!< Auto-Negotiation process completed */ 221 #define PHY_LINKED_STATUS ((uint16_t)0x0004U) /*!< Valid link established */ 222 #define PHY_JABBER_DETECTION ((uint16_t)0x0002U) /*!< Jabber condition detected */ 223 224 /* Section 4: Extended PHY Registers */ 225 #define PHY_SR ((uint16_t)0x10U) /*!< PHY status register Offset */ 226 227 #define PHY_SPEED_STATUS ((uint16_t)0x0002U) /*!< PHY Speed mask */ 228 #define PHY_DUPLEX_STATUS ((uint16_t)0x0004U) /*!< PHY Duplex mask */ 229 230 /* ################## SPI peripheral configuration ########################## */ 231 232 /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver 233 * Activated: CRC code is present inside driver 234 * Deactivated: CRC code cleaned from driver 235 */ 236 237 #define USE_SPI_CRC 0U 238 239 /* Includes ------------------------------------------------------------------*/ 240 /** 241 * @brief Include module's header file 242 */ 243 244 #ifdef HAL_RCC_MODULE_ENABLED 245 #include "stm32f4xx_hal_rcc.h" 246 #endif /* HAL_RCC_MODULE_ENABLED */ 247 248 #ifdef HAL_EXTI_MODULE_ENABLED 249 #include "stm32f4xx_hal_exti.h" 250 #endif /* HAL_EXTI_MODULE_ENABLED */ 251 252 #ifdef HAL_GPIO_MODULE_ENABLED 253 #include "stm32f4xx_hal_gpio.h" 254 #endif /* HAL_GPIO_MODULE_ENABLED */ 255 256 #ifdef HAL_DMA_MODULE_ENABLED 257 #include "stm32f4xx_hal_dma.h" 258 #endif /* HAL_DMA_MODULE_ENABLED */ 259 260 #ifdef HAL_CORTEX_MODULE_ENABLED 261 #include "stm32f4xx_hal_cortex.h" 262 #endif /* HAL_CORTEX_MODULE_ENABLED */ 263 264 #ifdef HAL_ADC_MODULE_ENABLED 265 #include "stm32f4xx_hal_adc.h" 266 #endif /* HAL_ADC_MODULE_ENABLED */ 267 268 #ifdef HAL_CAN_MODULE_ENABLED 269 #include "stm32f4xx_hal_can.h" 270 #endif /* HAL_CAN_MODULE_ENABLED */ 271 272 #ifdef HAL_CRC_MODULE_ENABLED 273 #include "stm32f4xx_hal_crc.h" 274 #endif /* HAL_CRC_MODULE_ENABLED */ 275 276 #ifdef HAL_CRYP_MODULE_ENABLED 277 #include "stm32f4xx_hal_cryp.h" 278 #endif /* HAL_CRYP_MODULE_ENABLED */ 279 280 #ifdef HAL_DMA2D_MODULE_ENABLED 281 #include "stm32f4xx_hal_dma2d.h" 282 #endif /* HAL_DMA2D_MODULE_ENABLED */ 283 284 #ifdef HAL_DAC_MODULE_ENABLED 285 #include "stm32f4xx_hal_dac.h" 286 #endif /* HAL_DAC_MODULE_ENABLED */ 287 288 #ifdef HAL_DCMI_MODULE_ENABLED 289 #include "stm32f4xx_hal_dcmi.h" 290 #endif /* HAL_DCMI_MODULE_ENABLED */ 291 292 #ifdef HAL_ETH_MODULE_ENABLED 293 #include "stm32f4xx_hal_eth.h" 294 #endif /* HAL_ETH_MODULE_ENABLED */ 295 296 #ifdef HAL_FLASH_MODULE_ENABLED 297 #include "stm32f4xx_hal_flash.h" 298 #endif /* HAL_FLASH_MODULE_ENABLED */ 299 300 #ifdef HAL_SRAM_MODULE_ENABLED 301 #include "stm32f4xx_hal_sram.h" 302 #endif /* HAL_SRAM_MODULE_ENABLED */ 303 304 #ifdef HAL_NOR_MODULE_ENABLED 305 #include "stm32f4xx_hal_nor.h" 306 #endif /* HAL_NOR_MODULE_ENABLED */ 307 308 #ifdef HAL_NAND_MODULE_ENABLED 309 #include "stm32f4xx_hal_nand.h" 310 #endif /* HAL_NAND_MODULE_ENABLED */ 311 312 #ifdef HAL_PCCARD_MODULE_ENABLED 313 #include "stm32f4xx_hal_pccard.h" 314 #endif /* HAL_PCCARD_MODULE_ENABLED */ 315 316 #ifdef HAL_SDRAM_MODULE_ENABLED 317 #include "stm32f4xx_hal_sdram.h" 318 #endif /* HAL_SDRAM_MODULE_ENABLED */ 319 320 #ifdef HAL_HASH_MODULE_ENABLED 321 #include "stm32f4xx_hal_hash.h" 322 #endif /* HAL_HASH_MODULE_ENABLED */ 323 324 #ifdef HAL_I2C_MODULE_ENABLED 325 #include "stm32f4xx_hal_i2c.h" 326 #endif /* HAL_I2C_MODULE_ENABLED */ 327 328 #ifdef HAL_I2S_MODULE_ENABLED 329 #include "stm32f4xx_hal_i2s.h" 330 #endif /* HAL_I2S_MODULE_ENABLED */ 331 332 #ifdef HAL_IWDG_MODULE_ENABLED 333 #include "stm32f4xx_hal_iwdg.h" 334 #endif /* HAL_IWDG_MODULE_ENABLED */ 335 336 #ifdef HAL_LTDC_MODULE_ENABLED 337 #include "stm32f4xx_hal_ltdc.h" 338 #endif /* HAL_LTDC_MODULE_ENABLED */ 339 340 #ifdef HAL_PWR_MODULE_ENABLED 341 #include "stm32f4xx_hal_pwr.h" 342 #endif /* HAL_PWR_MODULE_ENABLED */ 343 344 #ifdef HAL_RNG_MODULE_ENABLED 345 #include "stm32f4xx_hal_rng.h" 346 #endif /* HAL_RNG_MODULE_ENABLED */ 347 348 #ifdef HAL_RTC_MODULE_ENABLED 349 #include "stm32f4xx_hal_rtc.h" 350 #endif /* HAL_RTC_MODULE_ENABLED */ 351 352 #ifdef HAL_SAI_MODULE_ENABLED 353 #include "stm32f4xx_hal_sai.h" 354 #endif /* HAL_SAI_MODULE_ENABLED */ 355 356 #ifdef HAL_SD_MODULE_ENABLED 357 #include "stm32f4xx_hal_sd.h" 358 #endif /* HAL_SD_MODULE_ENABLED */ 359 360 #ifdef HAL_MMC_MODULE_ENABLED 361 #include "stm32f4xx_hal_mmc.h" 362 #endif /* HAL_MMC_MODULE_ENABLED */ 363 364 #ifdef HAL_SPI_MODULE_ENABLED 365 #include "stm32f4xx_hal_spi.h" 366 #endif /* HAL_SPI_MODULE_ENABLED */ 367 368 #ifdef HAL_TIM_MODULE_ENABLED 369 #include "stm32f4xx_hal_tim.h" 370 #endif /* HAL_TIM_MODULE_ENABLED */ 371 372 #ifdef HAL_UART_MODULE_ENABLED 373 #include "stm32f4xx_hal_uart.h" 374 #endif /* HAL_UART_MODULE_ENABLED */ 375 376 #ifdef HAL_USART_MODULE_ENABLED 377 #include "stm32f4xx_hal_usart.h" 378 #endif /* HAL_USART_MODULE_ENABLED */ 379 380 #ifdef HAL_IRDA_MODULE_ENABLED 381 #include "stm32f4xx_hal_irda.h" 382 #endif /* HAL_IRDA_MODULE_ENABLED */ 383 384 #ifdef HAL_SMARTCARD_MODULE_ENABLED 385 #include "stm32f4xx_hal_smartcard.h" 386 #endif /* HAL_SMARTCARD_MODULE_ENABLED */ 387 388 #ifdef HAL_WWDG_MODULE_ENABLED 389 #include "stm32f4xx_hal_wwdg.h" 390 #endif /* HAL_WWDG_MODULE_ENABLED */ 391 392 #ifdef HAL_PCD_MODULE_ENABLED 393 #include "stm32f4xx_hal_pcd.h" 394 #endif /* HAL_PCD_MODULE_ENABLED */ 395 396 #ifdef HAL_HCD_MODULE_ENABLED 397 #include "stm32f4xx_hal_hcd.h" 398 #endif /* HAL_HCD_MODULE_ENABLED */ 399 400 #ifdef HAL_DSI_MODULE_ENABLED 401 #include "stm32f4xx_hal_dsi.h" 402 #endif /* HAL_DSI_MODULE_ENABLED */ 403 404 #ifdef HAL_QSPI_MODULE_ENABLED 405 #include "stm32f4xx_hal_qspi.h" 406 #endif /* HAL_QSPI_MODULE_ENABLED */ 407 408 #ifdef HAL_CEC_MODULE_ENABLED 409 #include "stm32f4xx_hal_cec.h" 410 #endif /* HAL_CEC_MODULE_ENABLED */ 411 412 #ifdef HAL_FMPI2C_MODULE_ENABLED 413 #include "stm32f4xx_hal_fmpi2c.h" 414 #endif /* HAL_FMPI2C_MODULE_ENABLED */ 415 416 #ifdef HAL_SPDIFRX_MODULE_ENABLED 417 #include "stm32f4xx_hal_spdifrx.h" 418 #endif /* HAL_SPDIFRX_MODULE_ENABLED */ 419 420 #ifdef HAL_DFSDM_MODULE_ENABLED 421 #include "stm32f4xx_hal_dfsdm.h" 422 #endif /* HAL_DFSDM_MODULE_ENABLED */ 423 424 #ifdef HAL_LPTIM_MODULE_ENABLED 425 #include "stm32f4xx_hal_lptim.h" 426 #endif /* HAL_LPTIM_MODULE_ENABLED */ 427 428 /* Exported macro ------------------------------------------------------------*/ 429 #ifdef USE_FULL_ASSERT 430 /** 431 * @brief The assert_param macro is used for function's parameters check. 432 * @param expr: If expr is false, it calls assert_failed function 433 * which reports the name of the source file and the source 434 * line number of the call that failed. 435 * If expr is true, it returns no value. 436 * @retval None 437 */ 438 #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) 439 /* Exported functions ------------------------------------------------------- */ 440 void assert_failed(uint8_t* file, uint32_t line); 441 #else 442 #define assert_param(expr) ((void)0U) 443 #endif /* USE_FULL_ASSERT */ 444 445 #ifdef __cplusplus 446 } 447 #endif 448 449 #endif /* __STM32F4xx_HAL_CONF_H */ 450 451 452 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ 453