Home
last modified time | relevance | path

Searched +full:dcd +full:- +full:gpios (Results 1 – 25 of 36) sorted by relevance

12

/linux-6.14.4/Documentation/devicetree/bindings/serial/
Dcirrus,clps711x-uart.txt4 - compatible: Should be "cirrus,ep7209-uart".
5 - reg: Address and length of the register set for the device.
6 - interrupts: Should contain UART TX and RX interrupt.
7 - clocks: Should contain UART core clock number.
8 - syscon: Phandle to SYSCON node, which contain UART control bits.
11 - {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD
23 compatible = "cirrus,ep7312-uart","cirrus,ep7209-uart";
28 cts-gpios = <&sysgpio 0 GPIO_ACTIVE_LOW>;
29 dsr-gpios = <&sysgpio 1 GPIO_ACTIVE_LOW>;
30 dcd-gpios = <&sysgpio 2 GPIO_ACTIVE_LOW>;
Dserial.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Rob Herring <[email protected]>
11 - Greg Kroah-Hartman <[email protected]>
19 where N is the port number (non-negative decimal integer) as printed on the
28 cts-gpios:
34 dcd-gpios:
38 the UART's DCD line.
40 dsr-gpios:
[all …]
D8250.yaml3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - [email protected]
13 - $ref: serial.yaml#
14 - $ref: /schemas/memory-controllers/mc-peripheral-props.yaml#
15 - if:
17 - required:
18 - aspeed,lpc-io-reg
19 - required:
20 - aspeed,lpc-interrupts
[all …]
Dfsl-mxs-auart.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/serial/fsl-mxs-auart.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Fabio Estevam <[email protected]>
13 - $ref: serial.yaml#
18 - const: fsl,imx23-auart
19 - const: alphascale,asm9260-auart
20 - items:
21 - enum:
[all …]
D8250_omap.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Vignesh Raghavendra <[email protected]>
13 - $ref: /schemas/serial/serial.yaml#
14 - $ref: /schemas/serial/rs485.yaml#
19 - enum:
20 - ti,am3352-uart
21 - ti,am4372-uart
22 - ti,am654-uart
[all …]
Datmel,at91-usart.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
4 ---
5 $id: http://devicetree.org/schemas/serial/atmel,at91-usart.yaml#
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Richard Genoud <[email protected]>
16 - enum:
17 - atmel,at91rm9200-usart
18 - atmel,at91sam9260-usart
19 - items:
20 - const: atmel,at91rm9200-dbgu
[all …]
/linux-6.14.4/arch/arm/boot/dts/ti/omap/
Dam335x-netcom-plus-2xx.dts1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
11 /dts-v1/;
13 #include "am335x-baltos.dtsi"
14 #include "am335x-baltos-leds.dtsi"
21 uart1_pins: uart1-pins {
22 pinctrl-single,pins = <
29 AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_INPUT_PULLDOWN, MUX_MODE7) /* DCD */
34 uart2_pins: uart2-pins {
35 pinctrl-single,pins = <
[all …]
Dam335x-baltos-ir3220.dts1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
11 /dts-v1/;
13 #include "am335x-baltos.dtsi"
14 #include "am335x-baltos-leds.dtsi"
21 tca6416_pins: tca6416-pins {
22 pinctrl-single,pins = <
27 uart1_pins: uart1-pins {
28 pinctrl-single,pins = <
35 …M33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_INPUT_PULLDOWN, MUX_MODE7) /* lcd_pclk.gpio2[24] DCD */
[all …]
Dam335x-baltos-ir5221.dts1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
11 /dts-v1/;
13 #include "am335x-baltos.dtsi"
14 #include "am335x-baltos-leds.dtsi"
21 tca6416_pins: tca6416-pins {
22 pinctrl-single,pins = <
28 dcan1_pins: dcan1-pins {
29 pinctrl-single,pins = <
35 uart1_pins: uart1-pins {
[all …]
Dam335x-baltos-ir2110.dts1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
11 /dts-v1/;
13 #include "am335x-baltos.dtsi"
14 #include "am335x-baltos-leds.dtsi"
21 uart1_pins: uart1-pins {
22 pinctrl-single,pins = <
29 …M33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_INPUT_PULLDOWN, MUX_MODE7) /* lcd_pclk.gpio2[24] DCD */
34 mmc1_pins: mmc1-pins {
35 pinctrl-single,pins = <
[all …]
/linux-6.14.4/Documentation/devicetree/bindings/net/
Dintel,ixp4xx-hss.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
4 ---
5 $id: http://devicetree.org/schemas/net/intel,ixp4xx-hss.yaml#
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Linus Walleij <[email protected]>
20 const: intel,ixp4xx-hss
26 intel,npe-handle:
27 $ref: /schemas/types.yaml#/definitions/phandle-array
30 - description: phandle to the NPE this HSS instance is using
31 - description: the NPE instance number
[all …]
/linux-6.14.4/arch/arm/boot/dts/nxp/imx/
Dimx6dl-eckelmann-ci4x10.dts1 // SPDX-License-Identifier: GPL-2.0
7 /dts-v1/;
9 #include <dt-bindings/gpio/gpio.h>
15 compatible = "eckelmann,imx6dl-ci4x10", "fsl,imx6dl";
18 stdout-path = &uart3;
26 rmii_clk: clock-rmii {
28 compatible = "fixed-clock";
29 #clock-cells = <0>;
30 clock-frequency = <50000000>;
31 clock-output-names = "enet_ref_pad";
[all …]
Dimx6ull-colibri.dtsi1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
3 * Copyright 2018-2022 Toradex
16 compatible = "pwm-backlight";
17 brightness-levels = <0 4 8 16 32 64 128 255>;
18 default-brightness-level = <6>;
19 enable-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
20 pinctrl-names = "default";
21 pinctrl-0 = <&pinctrl_gpio_bl_on>;
22 power-supply = <&reg_3v3>;
28 compatible = "gpio-usb-b-connector", "usb-b-connector";
[all …]
Dimx6qdl-dhcom-som.dtsi1 // SPDX-License-Identifier: GPL-2.0+
3 * Copyright (C) 2015-2021 DH electronics GmbH
7 #include <dt-bindings/pwm/pwm.h>
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/clock/imx6qdl-clock.h>
10 #include <dt-bindings/input/input.h>
30 memory@10000000 { /* Appropriate memory size will be filled by U-Boot */
35 reg_3p3v: regulator-3P3V {
36 compatible = "regulator-fixed";
37 regulator-always-on;
[all …]
/linux-6.14.4/arch/arm/boot/dts/intel/ixp/
Dintel-ixp42x-goramo-multilink.dts1 // SPDX-License-Identifier: ISC
5 * - MultiLink Basic (a box)
6 * - MultiLink Max (19" rack mount)
9 * This is one of the few devices supporting the IXP4xx High-Speed Serial
14 /dts-v1/;
16 #include "intel-ixp42x.dtsi"
17 #include <dt-bindings/input/input.h>
21 compatible = "goramo,multilink-router", "intel,ixp42x";
22 #address-cells = <1>;
23 #size-cells = <1>;
[all …]
/linux-6.14.4/Documentation/devicetree/bindings/soc/fsl/cpm_qe/
Dserial.txt4 - fsl,cpm1-smc-uart
5 - fsl,cpm2-smc-uart
6 - fsl,cpm1-scc-uart
7 - fsl,cpm2-scc-uart
8 - fsl,qe-uart
10 Modem control lines connected to GPIO controllers are listed in the gpios
11 property as described in booting-without-of.txt, section IX.1 in the following
14 CTS, RTS, DCD, DSR, DTR, and RI.
16 The gpios property is optional and can be left out when control lines are
23 compatible = "fsl,mpc8272-scc-uart",
[all …]
/linux-6.14.4/Documentation/devicetree/bindings/firmware/
Dintel,ixp4xx-network-processing-engine.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
4 ---
5 $id: http://devicetree.org/schemas/firmware/intel,ixp4xx-network-processing-engine.yaml#
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Linus Walleij <[email protected]>
24 - items:
25 - const: intel,ixp4xx-network-processing-engine
29 - description: NPE0 (NPE-A) register range
30 - description: NPE1 (NPE-B) register range
31 - description: NPE2 (NPE-C) register range
[all …]
/linux-6.14.4/arch/arm/mach-sa1100/
Dh3xxx.c1 // SPDX-License-Identifier: GPL-2.0-only
16 #include <linux/platform_data/gpio-htc-egpio.h>
17 #include <linux/platform_data/sa11x0-serial.h>
37 .mask_flags = MTD_WRITEABLE, /* force read-only */
88 if (port->mapbase == _Ser3UTCR0) { in h3xxx_uart_pm()
105 int err = -EINVAL; in h3xxx_uart_set_wake()
107 if (port->mapbase == _Ser3UTCR0) { in h3xxx_uart_set_wake()
109 PWER |= PWER_GPIO23 | PWER_GPIO25; /* DCD and CTS */ in h3xxx_uart_set_wake()
111 PWER &= ~(PWER_GPIO23 | PWER_GPIO25); /* DCD and CTS */ in h3xxx_uart_set_wake()
123 .dev_id = "sa11x0-uart.3",
[all …]
/linux-6.14.4/arch/arm/boot/dts/microchip/
Dat91-wb50n.dtsi1 // SPDX-License-Identifier: GPL-2.0
3 * at91-wb50n.dtsi - Device Tree include file for wb50n cpu module
12 model = "Laird Workgroup Bridge 50N - Atmel SAMA5D";
17 stdout-path = "serial0:115200n8";
38 clock-frequency = <32768>;
42 clock-frequency = <12000000>;
46 atmel,osc-bypass;
50 pinctrl-names = "default";
51 pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
52 cd-gpios = <&pioC 26 GPIO_ACTIVE_LOW>;
[all …]
/linux-6.14.4/drivers/net/wan/
Dixp4xx_hss.c1 // SPDX-License-Identifier: GPL-2.0-only
5 * Copyright (C) 2007-2008 Krzysztof Hałasa <[email protected]>
13 #include <linux/dma-mapping.h>
90 #define PKT_HDLC_CRC_32 0x2 /* default = CRC-16 */
142 /* 56k data endiannes - which bit unused: high (default) or low */
180 * The clock sequence consists of (C - B) states of 0s and 1s, each state is
192 * The sequence takes (C - B) * A + (B + 1) * (A + 1) = 5 * 2 + 3 * 3 bits
201 #define TDMMAP_HDLC 1 /* HDLC - packetized */
202 #define TDMMAP_VOICE56K 2 /* Voice56K - 7-bit channelized */
203 #define TDMMAP_VOICE64K 3 /* Voice64K - 8-bit channelized */
[all …]
/linux-6.14.4/drivers/tty/serial/
Dserial_mctrl_gpio.c1 // SPDX-License-Identifier: GPL-2.0+
34 { "dcd", TIOCM_CD, GPIOD_IN, },
46 * mctrl_gpio_set - set gpios according to mctrl state
47 * @gpios: gpios to set
50 * Set the gpios according to the mctrl state.
52 void mctrl_gpio_set(struct mctrl_gpios *gpios, unsigned int mctrl) in mctrl_gpio_set() argument
59 if (gpios == NULL) in mctrl_gpio_set()
63 if (gpios->gpio[i] && mctrl_gpio_flags_is_dir_out(i)) { in mctrl_gpio_set()
64 desc_array[count] = gpios->gpio[i]; in mctrl_gpio_set()
74 * mctrl_gpio_to_gpiod - obtain gpio_desc of modem line index
[all …]
/linux-6.14.4/arch/arm64/boot/dts/freescale/
Dimx8mm-venice-gw7902.dts1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 /dts-v1/;
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/linux-event-codes.h>
10 #include <dt-bindings/leds/common.h>
11 #include <dt-bindings/net/ti-dp83867.h>
12 #include <dt-bindings/phy/phy-imx8-pcie.h>
18 compatible = "gw,imx8mm-gw7902", "fsl,imx8mm";
29 stdout-path = &uart2;
38 compatible = "fixed-clock";
[all …]
Dimx8mm-venice-gw7903.dts1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 /dts-v1/;
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/linux-event-codes.h>
10 #include <dt-bindings/leds/common.h>
11 #include <dt-bindings/phy/phy-imx8-pcie.h>
17 compatible = "gw,imx8mm-gw7903", "fsl,imx8mm";
27 stdout-path = &uart2;
35 gpio-keys {
36 compatible = "gpio-keys";
[all …]
Dimx8mm-venice-gw7901.dts1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 /dts-v1/;
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/linux-event-codes.h>
10 #include <dt-bindings/leds/common.h>
11 #include <dt-bindings/phy/phy-imx8-pcie.h>
17 compatible = "gw,imx8mm-gw7901", "fsl,imx8mm";
32 stdout-path = &uart2;
40 gpio-keys {
41 compatible = "gpio-keys";
[all …]
/linux-6.14.4/arch/arm/boot/dts/gemini/
Dgemini-dlink-dir-685.dts2 * Device Tree file for D-Link DIR-685 Xtreme N Storage Router
5 /dts-v1/;
8 #include <dt-bindings/input/input.h>
11 model = "D-Link DIR-685 Xtreme N Storage Router";
12 compatible = "dlink,dir-685", "cortina,gemini";
13 #address-cells = <1>;
14 #size-cells = <1>;
17 /* 128 MB SDRAM in 2 x Hynix HY5DU121622DTP-D43 */
24 stdout-path = "uart0:19200n8";
28 compatible = "gpio-keys";
[all …]

12