Home
last modified time | relevance | path

Searched full:gusb2phycfg (Results 1 – 7 of 7) sorted by relevance

/linux-6.14.4/drivers/usb/dwc3/
Ddebugfs.c95 dump_register(GUSB2PHYCFG(0)),
96 dump_register(GUSB2PHYCFG(1)),
97 dump_register(GUSB2PHYCFG(2)),
98 dump_register(GUSB2PHYCFG(3)),
99 dump_register(GUSB2PHYCFG(4)),
100 dump_register(GUSB2PHYCFG(5)),
101 dump_register(GUSB2PHYCFG(6)),
102 dump_register(GUSB2PHYCFG(7)),
103 dump_register(GUSB2PHYCFG(8)),
104 dump_register(GUSB2PHYCFG(9)),
[all …]
Ddrd.c230 /* GUSB2PHYCFG.ULPIAutoRes = 1/0, GUSB2PHYCFG.SusPHY = 1 */ in dwc3_otg_host_init()
293 /* GUSB2PHYCFG.ULPIAutoRes = 0, GUSB2PHYCFG0.SusPHY = 1 */ in dwc3_otg_device_init()
Dcore.c143 * GUSB2PHYCFG.SUSPHY should be cleared during mode switching, in dwc3_set_prtcap()
754 /* Ensure the GUSB2PHYCFG.SUSPHY is cleared prior to phy init. */ in dwc3_hs_phy_setup()
769 * ULPIEXTVBUSDRV bit[17] of the GUSB2PHYCFG register to drive vBus in dwc3_hs_phy_setup()
837 * Make sure GUSB3PIPECTL.SUSPENDENABLE and GUSB2PHYCFG.SUSPHY are clear in dwc3_phy_init()
842 * GUSB2PHYCFG.SUSPHY are set soon after initialization to avoid in dwc3_phy_init()
2482 /* Restore GUSB2PHYCFG bits that were modified in suspend */ in dwc3_resume_common()
Dgadget.c299 * GUSB2PHYCFG.SUSPENDUSB2, which turns on the signal required to complete
320 * When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or in dwc3_send_gadget_ep_cmd()
321 * GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an in dwc3_send_gadget_ep_cmd()
324 * Save and clear both GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY in dwc3_send_gadget_ep_cmd()
2639 * GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY are cleared before starting in dwc3_gadget_run_stop()
Dcore.h1119 * @dis_enblslpm_quirk: set if we clear enblslpm in GUSB2PHYCFG,
1127 * in GUSB2PHYCFG, specify that USB2 PHY doesn't
/linux-6.14.4/Documentation/devicetree/bindings/usb/
Dsnps,dwc3-common.yaml145 When set clears the enblslpm in GUSB2PHYCFG, disabling the suspend signal
164 When set, clear the u2_freeclk_exists in GUSB2PHYCFG, specify that USB2
/linux-6.14.4/drivers/phy/broadcom/
Dphy-brcm-usb-init-synopsys.c157 USB_XHCI_GBL_UNSET(xhci_gbl, GUSB2PHYCFG, in xhci_soft_reset()