xref: /aosp_15_r20/hardware/interfaces/wifi/hostapd/1.1/IHostapd.hal (revision 4d7e907c777eeecc4c5bd7cf640a754fac206ff7)

/*
 * Copyright 2018 The Android Open Source Project
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *      http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */

package [email protected];

import @1.0::IHostapd;
import @1.0::HostapdStatus;

import IHostapdCallback;

/**
 * Top-level object for managing SoftAPs.
 */
interface IHostapd extends @1.0::IHostapd {
    /**
     * Parameters to specify the channel range for ACS.
     */
    struct AcsChannelRange {
        /**
         * Channel number (IEEE 802.11) at the start of the range.
         */
        uint32_t start;
        /**
         * Channel number (IEEE 802.11) at the end of the range.
         */
        uint32_t end;
    };

    /**
     * Parameters to control the channel selection for the interface.
     */
    struct ChannelParams {
        /**
         * This option can be used to specify the channels selected by ACS.
         * If this is an empty list, all channels allowed in selected HW mode
         * are specified implicitly.
         * Note: channels may be overridden by firmware.
         * Note: this option is ignored if ACS is disabled.
         */
        vec<AcsChannelRange> acsChannelRanges;
    };

    /**
     * Parameters to use for setting up the access point interface.
     */
    struct IfaceParams {
        /**
         * Baseline information as defined in HAL 1.0.
         */
        @1.0::IHostapd.IfaceParams V1_0;
        /** Additional Channel params for the interface */
        ChannelParams channelParams;
    };

    /**
     * Adds a new access point for hostapd to control.
     *
     * This should trigger the setup of an access point with the specified
     * interface and network params.
     *
     * @param ifaceParams AccessPoint Params for the access point.
     * @param nwParams Network Params for the access point.
     * @return status Status of the operation.
     *         Possible status codes:
     *         |HostapdStatusCode.SUCCESS|,
     *         |HostapdStatusCode.FAILURE_ARGS_INVALID|,
     *         |HostapdStatusCode.FAILURE_UNKNOWN|,
     *         |HostapdStatusCode.FAILURE_IFACE_EXISTS|
     */
    addAccessPoint_1_1(IfaceParams ifaceParams, NetworkParams nwParams)
        generates(HostapdStatus status);

    /**
     * Register for callbacks from the hostapd service.
     *
     * These callbacks are invoked for global events that are not specific
     * to any interface or network. Registration of multiple callback
     * objects is supported. These objects must be deleted when the corresponding
     * client process is dead.
     *
     * @param callback An instance of the |IHostapdCallback| HIDL interface
     *     object.
     * @return status Status of the operation.
     *     Possible status codes:
     *     |HostapdStatusCode.SUCCESS|,
     *     |HostapdStatusCode.FAILURE_UNKNOWN|
     */
    registerCallback(IHostapdCallback callback)
        generates (HostapdStatus status);
};