Home
last modified time | relevance | path

Searched +full:switch +full:- +full:gpios (Results 1 – 25 of 855) sorted by relevance

12345678910>>...35

/linux-6.14.4/arch/arm/boot/dts/ti/omap/
Dam3517-evm.dts1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
5 /dts-v1/;
8 #include "am3517-som.dtsi"
9 #include "am3517-evm-ui.dtsi"
10 #include <dt-bindings/input/input.h>
14 compatible = "ti,am3517-evm", "ti,am3517", "ti,omap3";
21 stdout-path = &uart3;
30 compatible = "regulator-fixed";
31 regulator-name = "vmmc_fixed";
[all …]
/linux-6.14.4/Documentation/devicetree/bindings/usb/
Dgpio-sbu-mux.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/usb/gpio-sbu-mux.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: GPIO-based SBU mux
10 - Bjorn Andersson <[email protected]>
13 In USB Type-C applications the SBU lines needs to be connected, disconnected
21 - enum:
22 - nxp,cbdtu02043
23 - onnn,fsusb42
[all …]
/linux-6.14.4/Documentation/devicetree/bindings/sound/
Dnokia,rx51.txt4 - compatible: Should contain "nokia,n900-audio"
5 - nokia,cpu-dai: phandle for the McBSP node
6 - nokia,audio-codec: phandles for the main TLV320AIC3X node and the
8 - nokia,headphone-amplifier: phandle for the TPA6130A2 node
9 - tvout-selection-gpios: GPIO for tvout selection
10 - jack-detection-gpios: GPIO for jack detection
11 - eci-switch-gpios: GPIO for ECI (Enhancement Control Interface) switch
12 - speaker-amplifier-gpios: GPIO for speaker amplifier
17 compatible = "nokia,n900-audio";
19 nokia,cpu-dai = <&mcbsp2>;
[all …]
Dsirf-audio.txt4 - compatible: "sirf,sirf-audio-card"
5 - sirf,audio-platform: phandle for the platform node
6 - sirf,audio-codec: phandle for the SiRF internal codec node
9 - hp-pa-gpios: Need to be present if the board need control external
11 - spk-pa-gpios: Need to be present if the board need control external
13 - hp-switch-gpios: Need to be present if the board capable to detect jack
16 Available audio endpoints for the audio-routing table:
34 compatible = "sirf,sirf-audio-card";
35 sirf,audio-codec = <&audiocodec>;
36 sirf,audio-platform = <&audioport>;
[all …]
/linux-6.14.4/Documentation/devicetree/bindings/iio/frequency/
Dadi,admfm2000.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
4 ---
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Kim Seer Paller <[email protected]>
22 - adi,admfm2000
24 '#address-cells':
27 '#size-cells':
31 "^channel@[0-1]$":
44 adi,mixer-mode:
52 switch-gpios:
[all …]
/linux-6.14.4/arch/arm/boot/dts/marvell/
Dkirkwood-linkstation-6282.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
3 * Device Tree common file for kirkwood-6282 based Buffalo Linkstation
10 #include "kirkwood-6282.dtsi"
11 #include "kirkwood-linkstation.dtsi"
15 pinctrl: pin-controller@10000 {
16 pmx_power_hdd0: pmx-power-hdd0 {
20 pmx_usb_vbus: pmx-usb-vbus {
24 pmx_fan_high: pmx-fan-high {
28 pmx_fan_low: pmx-fan-low {
32 pmx_led_alarm: pmx-led-alarm {
[all …]
Dkirkwood-linkstation-duo-6281.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
3 * Device Tree common file for kirkwood-6281 based 2-Bay Buffalo Linkstation
10 #include "kirkwood-6281.dtsi"
11 #include "kirkwood-linkstation.dtsi"
15 pinctrl: pin-controller@10000 {
16 pmx_power_hdd0: pmx-power-hdd0 {
20 pmx_power_hdd1: pmx-power-hdd1 {
24 pmx_usb_vbus: pmx-usb-vbus {
28 pmx_led_alarm: pmx-led-alarm {
32 pmx_led_function_red: pmx-led-function-red {
[all …]
Dkirkwood-lsxl.dtsi1 // SPDX-License-Identifier: GPL-2.0
3 #include "kirkwood-6281.dtsi"
8 stdout-path = &uart0;
12 pinctrl: pin-controller@10000 {
13 /* Non-default UART pins */
14 pmx_uart0: pmx-uart0 {
18 pmx_power_hdd: pmx-power-hdd {
22 pmx_usb_vbus: pmx-usb-vbus {
26 pmx_fan_high: pmx-fan-high {
30 pmx_fan_low: pmx-fan-low {
[all …]
Dorion5x-linkstation-lschl.dts2 * Device Tree file for Buffalo Linkstation LS-CHLv3
5 * Copyright (C) 2015-2017
8 * This file is dual-licensed: you can use it either under the terms
47 /dts-v1/;
49 #include "orion5x-linkstation.dtsi"
50 #include "mvebu-linkstation-gpio-simple.dtsi"
51 #include "mvebu-linkstation-fan.dtsi"
52 #include <dt-bindings/gpio/gpio.h>
55 model = "Buffalo Linkstation LiveV3 (LS-CHL)";
56 compatible = "buffalo,lschl", "marvell,orion5x-88f5182", "marvell,orion5x";
[all …]
Dorion5x-linkstation-lswtgl.dts2 * Device Tree file for Buffalo Linkstation LS-WTGL
7 * This file is dual-licensed: you can use it either under the terms
46 /dts-v1/;
48 #include "orion5x-linkstation.dtsi"
49 #include "mvebu-linkstation-gpio-simple.dtsi"
50 #include "mvebu-linkstation-fan.dtsi"
51 #include <dt-bindings/gpio/gpio.h>
54 model = "Buffalo Linkstation LS-WTGL";
55 compatible = "buffalo,lswtgl", "marvell,orion5x-88f5182", "marvell,orion5x";
63 power-on-switch {
[all …]
/linux-6.14.4/Documentation/devicetree/bindings/net/dsa/
Drealtek.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - $ref: dsa.yaml#/$defs/ethernet-ports
13 - Linus Walleij <[email protected]>
20 The SMI "Simple Management Interface" is a two-wire protocol using
21 bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does
23 SMI-based Realtek devices. The realtek-smi driver is a platform driver
26 The MDIO-connected switches use MDIO protocol to access their registers.
27 The realtek-mdio driver is an MDIO driver and it must be inserted inside
[all …]
/linux-6.14.4/arch/arm/boot/dts/nxp/imx/
Dimx6q-bx50v3.dtsi5 * This file is dual-licensed: you can use it either under the terms
43 #include "imx6q-ba16.dtsi"
46 mclk: clock-mclk {
47 compatible = "fixed-clock";
48 #clock-cells = <0>;
49 clock-frequency = <22000000>;
52 gpio-poweroff {
53 compatible = "gpio-poweroff";
54 gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
58 reg_wl18xx_vmmc: regulator-wl18xx {
[all …]
/linux-6.14.4/arch/arm/boot/dts/intel/ixp/
Dintel-ixp42x-linksys-wrv54g.dts1 // SPDX-License-Identifier: ISC
9 /dts-v1/;
11 #include "intel-ixp42x.dtsi"
12 #include <dt-bindings/input/input.h>
17 #address-cells = <1>;
18 #size-cells = <1>;
28 stdout-path = "uart1:115200n8";
39 compatible = "gpio-leds";
40 led-power {
42 gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
[all …]
/linux-6.14.4/arch/arm/boot/dts/microchip/
Dat91-kizbox3-hs.dts1 // SPDX-License-Identifier: GPL-2.0
3 * at91-kizbox3-hs.dts - Device Tree file for Overkiz KIZBOX3-HS board
11 /dts-v1/;
12 #include "at91-kizbox3_common.dtsi"
15 model = "Overkiz KIZBOX3-HS";
16 compatible = "overkiz,kizbox3-hs", "atmel,sama5d2", "atmel,sama5";
18 led-controller-1 {
21 led-1 {
25 led-2 {
29 led-3 {
[all …]
/linux-6.14.4/arch/arm/boot/dts/broadcom/
Dbcm4709-buffalo-wxr-1900dhp.dts1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
4 * DTS for Buffalo WXR-1900DHP
9 /dts-v1/;
12 #include "bcm5301x-nand-cs0-bch8.dtsi"
15 compatible = "buffalo,wxr-1900dhp", "brcm,bcm4709", "brcm,bcm4708";
16 model = "Buffalo WXR-1900DHP";
29 compatible = "gpio-leds";
31 led-usb {
33 gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
36 led-power-amber {
[all …]
Dbcm4708-buffalo-wzr-1750dhp.dts1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
4 * DTS for Buffalo WZR-1750DHP
9 /dts-v1/;
12 #include "bcm5301x-nand-cs0-bch8.dtsi"
15 compatible = "buffalo,wzr-1750dhp", "brcm,bcm4708";
16 model = "Buffalo WZR-1750DHP (BCM4708)";
29 compatible = "spi-gpio";
30 num-chipselects = <1>;
31 sck-gpios = <&chipcommon 7 0>;
32 mosi-gpios = <&chipcommon 4 0>;
[all …]
Dbcm4708-buffalo-wzr-1166dhp-common.dtsi1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
4 * DTS for Buffalo WZR-1166DHP and WZR-1166DHP2
12 #include "bcm5301x-nand-cs0-bch8.dtsi"
13 #include <dt-bindings/leds/common.h>
17 compatible = "spi-gpio";
18 num-chipselects = <1>;
19 sck-gpios = <&chipcommon 7 0>;
20 mosi-gpios = <&chipcommon 4 0>;
21 cs-gpios = <&chipcommon 6 0>;
22 #address-cells = <1>;
[all …]
/linux-6.14.4/arch/arm64/boot/dts/qcom/
Dmsm8916-wingtech-wt88047.dts1 // SPDX-License-Identifier: GPL-2.0-only
6 /dts-v1/;
8 #include "msm8916-pm8916.dtsi"
9 #include "msm8916-modem-qdsp6.dtsi"
11 #include <dt-bindings/gpio/gpio.h>
12 #include <dt-bindings/input/input.h>
13 #include <dt-bindings/leds/common.h>
18 chassis-type = "handset";
27 stdout-path = "serial0";
30 speaker_amp: audio-amplifier {
[all …]
/linux-6.14.4/arch/arm64/boot/dts/apple/
Ds800x-se.dtsi1 // SPDX-License-Identifier: GPL-2.0+ OR MIT
8 #include "s800-0-3-common.dtsi"
9 #include <dt-bindings/input/input.h>
12 chassis-type = "handset";
14 gpio-keys {
15 compatible = "gpio-keys";
17 button-home {
19 gpios = <&pinctrl_ap 96 GPIO_ACTIVE_LOW>;
21 wakeup-source;
24 button-power {
[all …]
Ds800x-6s.dtsi1 // SPDX-License-Identifier: GPL-2.0+ OR MIT
8 #include "s800-0-3-common.dtsi"
9 #include <dt-bindings/input/input.h>
12 chassis-type = "handset";
14 gpio-keys {
15 compatible = "gpio-keys";
17 button-home {
19 gpios = <&pinctrl_ap 96 GPIO_ACTIVE_LOW>;
21 wakeup-source;
24 button-power {
[all …]
Dt7000-mini4.dtsi1 // SPDX-License-Identifier: GPL-2.0+ OR MIT
9 #include "t7000-common.dtsi"
10 #include "t7000-handheld.dtsi"
11 #include <dt-bindings/input/input.h>
14 chassis-type = "tablet";
16 gpio-keys {
17 compatible = "gpio-keys";
19 button-home {
21 gpios = <&pinctrl 32 GPIO_ACTIVE_LOW>;
23 wakeup-source;
[all …]
Dt7000-6.dtsi1 // SPDX-License-Identifier: GPL-2.0+ OR MIT
7 #include <dt-bindings/input/input.h>
9 #include "t7000-common.dtsi"
10 #include "t7000-handheld.dtsi"
13 chassis-type = "handset";
15 gpio-keys {
16 compatible = "gpio-keys";
18 button-home {
20 gpios = <&pinctrl 32 GPIO_ACTIVE_LOW>;
22 wakeup-source;
[all …]
Ds5l8960x-5s.dtsi1 // SPDX-License-Identifier: GPL-2.0+ OR MIT
10 #include "s5l8960x-common.dtsi"
11 #include <dt-bindings/input/input.h>
14 chassis-type = "handset";
16 gpio-keys {
17 compatible = "gpio-keys";
19 button-home {
21 gpios = <&pinctrl 2 GPIO_ACTIVE_LOW>;
23 wakeup-source;
26 button-power {
[all …]
Ds5l8960x-air1.dtsi1 // SPDX-License-Identifier: GPL-2.0+ OR MIT
10 #include "s5l8960x-common.dtsi"
11 #include <dt-bindings/input/input.h>
14 chassis-type = "tablet";
16 gpio-keys {
17 compatible = "gpio-keys";
19 button-home {
21 gpios = <&pinctrl 2 GPIO_ACTIVE_LOW>;
23 wakeup-source;
26 button-power {
[all …]
Ds5l8960x-mini2.dtsi1 // SPDX-License-Identifier: GPL-2.0+ OR MIT
10 #include "s5l8960x-common.dtsi"
11 #include <dt-bindings/input/input.h>
14 chassis-type = "tablet";
16 gpio-keys {
17 compatible = "gpio-keys";
19 button-home {
21 gpios = <&pinctrl 2 GPIO_ACTIVE_LOW>;
23 wakeup-source;
26 button-power {
[all …]

12345678910>>...35