| /linux-6.14.4/Documentation/devicetree/bindings/regulator/ |
| D | ltc3589.txt | 8 - regulators: Contains eight regulator child nodes sw1, sw2, sw3, bb-out,
13 nodes for sw1, sw2, sw3, bb-out, ldo1, and ldo2 additionally need to specify
20 Regulators sw1, sw2, sw3, and ldo2 can regulate the feedback reference from
54 sw3_reg: sw3 {
|
| D | pv88060.txt | 11 BUCK1, LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, SW1, SW2, SW3, SW4,
97 SW3 {
98 regulator-name = "sw3";
|
| D | pfuze100.yaml | 19 sw1a,sw1b,sw2,sw3,swbst,vsnvs,vrefddr,vldo1,vldo2,vccsd,v33,vldo3,vldo4
21 sw1,sw2,sw3,vsnvs,vldo1,vldo2,vccsd,v33,vldo3,vldo4
|
| D | lltc,ltc3676.yaml | 126 sw3_reg: sw3 {
|
| /linux-6.14.4/Documentation/devicetree/bindings/mfd/ |
| D | mc13xxx.txt | 59 sw3 : regulator SW3 (register 29, bit 20)
88 sw3 : regulator SW3 (register 26, bit 0)
|
| /linux-6.14.4/arch/arm/boot/dts/nxp/mxs/ |
| D | imx28-eukrea-mbmx28lc.dtsi | 27 switch-sw3 {
28 label = "SW3";
182 gpio_button_sw3_pins_mbmx28lc: gpio-button-sw3-mbmx28lc@0 {
|
| /linux-6.14.4/arch/arm/boot/dts/nxp/imx/ |
| D | imx53-qsrb.dts | 56 sw3_reg: sw3 {
57 regulator-name = "SW3";
|
| D | imx6ul-tqma6ul-common.dtsi | 57 reg_sw3_ddr: sw3 {
|
| /linux-6.14.4/Documentation/hid/ |
| D | hid-alps.rst | 114 1 0 0 SW6 SW5 SW4 SW3 SW2 SW1
164 Byte1 1 1 1 0 1 SW3 SW2 SW1
173 SW1-SW3:
|
| /linux-6.14.4/drivers/hid/ |
| D | hid-ite.c | 31 /* For Acer Aspire Switch 10E (SW3-016) keyboard-dock */ in ite_report_fixup()
33 hid_info(hdev, "Fixing up Acer Aspire Switch 10E (SW3-016) ITE keyboard report descriptor\n"); in ite_report_fixup()
|
| /linux-6.14.4/drivers/media/dvb-frontends/ |
| D | dib0090.h | 87 extern int dib0090_set_switch(struct dvb_frontend *fe, u8 sw1, u8 sw2, u8 sw3);
157 u8 sw1, u8 sw2, u8 sw3) in dib0090_set_switch() argument
|
| /linux-6.14.4/drivers/regulator/ |
| D | ltc3676.c | 172 /* SW1, SW2, SW3, SW4 linear 0.8V-3.3V with scalar via R1/R2 feeback res */
227 LTC3676_LINEAR_REG(SW3, sw3, BUCK3, DVB3A),
|
| D | ltc3589.c | 128 /* SW1, SW2, SW3, LDO2 */
256 LTC3589_LINEAR_REG(SW3, sw3, B3DTV1),
|
| D | pcap-regulator.c | 133 /* SW3 STBY is on PCAP_REG_AUXVREG */
134 VREG_INFO(SW3, PCAP_REG_SWCTRL, 11, 12, 24, NA),
|
| D | pfuze100-regulator.c | 410 PFUZE3000_SW3_REG(PFUZE3000, SW3, PFUZE100_SW3AVOL, 900000, 1650000, 50000),
425 PFUZE3000_SW3_REG(PFUZE3001, SW3, PFUZE100_SW3AVOL, 900000, 1650000, 50000),
480 { .name = "sw3", },
497 { .name = "sw3", },
|
| D | mc13783-regulator.c | 253 MC13783_DEFINE_SW(SW3, sw3, SWITCHERS5, SWITCHERS5, mc13783_sw3_val),
|
| /linux-6.14.4/arch/arm/boot/dts/marvell/ |
| D | armada-388-clearfog-base.dts | 23 /* The rear SW3 button */
|
| D | armada-388-clearfog.dts | 40 /* The rear SW3 button */
|
| /linux-6.14.4/arch/sh/boards/mach-rsk/ |
| D | devices-rsk7203.c | 101 .desc = "SW3",
|
| /linux-6.14.4/arch/arm64/boot/dts/amlogic/ |
| D | meson-sm1-bananapi.dtsi | 19 button-sw3 {
20 label = "SW3";
|
| /linux-6.14.4/arch/arm/boot/dts/microchip/ |
| D | pm9g45.dts | 180 label = "SW3";
|
| /linux-6.14.4/Documentation/networking/ |
| D | arcnet-hardware.rst | 832 SW3 1-8: Node ID Select
848 The eight switches in group SW3 are used to set the node ID. Each node
1998 SW3 1-5: IRQ Select
2008 The eight switches in SW3 are used to set the node ID. Each node attached
2072 *) To enable the Boot ROM set the switch 8 of switch block SW3 to position ON.
2080 Switches 1-5 of the switch block SW3 control the IRQ level::
2095 The switches 6-7 of the switch block SW3 are used to determine the timeout
2851 | SW3 | || | |
2870 SW3 1-5: IRQ Select
2876 Although the jumpers SW1 and SW3 are marked SW, not JP, they are jumpers, not
[all …]
|
| /linux-6.14.4/arch/arm64/boot/dts/marvell/ |
| D | cn9130-cf-base.dts | 29 /* The rear SW3 button */
|
| /linux-6.14.4/arch/arm64/boot/dts/renesas/ |
| D | rzg2l-smarc.dtsi | 165 * SW3 should be at position 2->3 so that SER0_RX line is activated
|
| D | rzg2lc-smarc.dtsi | 182 * SW3 should be at position 2->3 so that SER0_RX line is activated
|