| /linux-6.14.4/arch/arm64/boot/dts/freescale/ |
| D | imx93-tqma9352-mba93xxla.dts | 1 // SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
3 * Copyright (c) 2022-2023 TQ-Systems GmbH <[email protected]-group.com>,
4 * D-82229 Seefeld, Germany.
8 /dts-v1/;
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/leds/common.h>
12 #include <dt-bindings/net/ti-dp83867.h>
13 #include <dt-bindings/pwm/pwm.h>
14 #include <dt-bindings/usb/pd.h>
15 #include "imx93-tqma9352.dtsi"
[all …]
|
| D | imx93-tqma9352-mba93xxca.dts | 1 // SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
3 * Copyright (c) 2022-2023 TQ-Systems GmbH <[email protected]-group.com>,
4 * D-82229 Seefeld, Germany.
8 /dts-v1/;
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/leds/common.h>
12 #include <dt-bindings/net/ti-dp83867.h>
13 #include <dt-bindings/pwm/pwm.h>
15 #include "imx93-tqma9352.dtsi"
18 model = "TQ-Systems i.MX93 TQMa93xxLA/TQMa93xxCA on MBa93xxCA starter kit";
[all …]
|
| D | imx8-ss-hsio.dtsi | 1 // SPDX-License-Identifier: GPL-2.0+
7 #include <dt-bindings/phy/phy.h>
9 hsio_axi_clk: clock-hsio-axi {
10 compatible = "fixed-clock";
11 #clock-cells = <0>;
12 clock-frequency = <400000000>;
13 clock-output-names = "hsio_axi_clk";
16 hsio_per_clk: clock-hsio-per {
17 compatible = "fixed-clock";
18 #clock-cells = <0>;
[all …]
|
| D | imx8qm-mek.dts | 1 // SPDX-License-Identifier: GPL-2.0+
3 * Copyright 2018-2019 NXP
7 /dts-v1/;
9 #include <dt-bindings/usb/pd.h>
14 compatible = "fsl,imx8qm-mek", "fsl,imx8qm";
17 stdout-path = &lpuart0;
21 /delete-node/ cpu-map;
22 /delete-node/ cpu@100;
23 /delete-node/ cpu@101;
26 thermal-zones {
[all …]
|
| D | imx8mn-var-som-symphony.dts | 1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
5 * Copyright 2019-2020 Variscite Ltd.
9 /dts-v1/;
11 #include <dt-bindings/usb/pd.h>
12 #include "imx8mn-var-som.dtsi"
15 model = "Variscite VAR-SOM-MX8MN Symphony evaluation board";
16 compatible = "variscite,var-som-mx8mn-symphony", "variscite,var-som-mx8mn", "fsl,imx8mn";
18 reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
19 compatible = "regulator-fixed";
20 pinctrl-names = "default";
[all …]
|
| D | imx8qxp-mek.dts | 1 // SPDX-License-Identifier: GPL-2.0+
6 /dts-v1/;
9 #include <dt-bindings/usb/pd.h>
13 compatible = "fsl,imx8qxp-mek", "fsl,imx8qxp";
15 bt_sco_codec: audio-codec-bt {
16 compatible = "linux,bt-sco";
17 #sound-dai-cells = <1>;
21 stdout-path = &lpuart0;
24 imx8x_cm4: imx8x-cm4 {
25 compatible = "fsl,imx8qxp-cm4";
[all …]
|
| /linux-6.14.4/arch/arm/mach-tegra/ |
| D | board-paz00.c | 1 // SPDX-License-Identifier: GPL-2.0-only
3 * arch/arm/mach-tegra/board-paz00.c
7 * Based on board-harmony.c
21 .name = "tegra-gpio",
27 PROPERTY_ENTRY_GPIO("reset-gpios",
29 PROPERTY_ENTRY_GPIO("shutdown-gpios",
42 struct platform_device *pd; in tegra_paz00_wifikill_init() local
52 pd = platform_device_register_full(&wifi_rfkill_info); in tegra_paz00_wifikill_init()
53 err = PTR_ERR_OR_ZERO(pd); in tegra_paz00_wifikill_init()
|
| /linux-6.14.4/Documentation/devicetree/bindings/connector/ |
| D | usb-connector.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only
3 ---
4 $id: http://devicetree.org/schemas/connector/usb-connector.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Rob Herring <[email protected]>
20 - enum:
21 - usb-a-connector
22 - usb-b-connector
23 - usb-c-connector
25 - items:
[all …]
|
| /linux-6.14.4/Documentation/devicetree/bindings/display/bridge/ |
| D | analogix,anx7814.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Analogix ANX7814 SlimPort (Full-HD Transmitter)
10 - Andrzej Hajda <[email protected]>
11 - Neil Armstrong <[email protected]>
12 - Robert Foss <[email protected]>
17 - analogix,anx7808
18 - analogix,anx7812
19 - analogix,anx7814
[all …]
|
| /linux-6.14.4/arch/arm/boot/dts/aspeed/ |
| D | aspeed-bmc-facebook-bletchley.dts | 1 // SPDX-License-Identifier: GPL-2.0+
3 /dts-v1/;
5 #include "aspeed-g6.dtsi"
6 #include <dt-bindings/gpio/aspeed-gpio.h>
7 #include <dt-bindings/usb/pd.h>
8 #include <dt-bindings/leds/leds-pca955x.h>
9 #include <dt-bindings/interrupt-controller/irq.h>
10 #include <dt-bindings/i2c/i2c.h>
14 compatible = "facebook,bletchley-bmc", "aspeed,ast2600";
29 iio-hwmon {
[all …]
|
| /linux-6.14.4/arch/x86/platform/geode/ |
| D | geode-common.c | 1 // SPDX-License-Identifier: GPL-2.0-only
3 * Shared helpers to register GPIO-connected buttons and LEDs
15 #include "geode-common.h"
18 .name = "cs5535-gpio",
22 PROPERTY_ENTRY_U32("poll-interval", 20),
27 .name = "geode-gpio-keys",
35 PROPERTY_ENTRY_U32("debounce-interval", 100),
52 * Creates gpio-keys-polled device for the restart key.
55 * because it registers gpiochip software node used by both gpio-keys and
56 * leds-gpio devices.
[all …]
|
| /linux-6.14.4/arch/arm64/boot/dts/allwinner/ |
| D | sun50i-h6-orangepi-3.dts | 1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
4 /dts-v1/;
6 #include "sun50i-h6.dtsi"
7 #include "sun50i-h6-cpu-opp.dtsi"
9 #include <dt-bindings/gpio/gpio.h>
13 compatible = "xunlong,orangepi-3", "allwinner,sun50i-h6";
21 stdout-path = "serial0:115200n8";
25 compatible = "hdmi-connector";
26 ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
31 remote-endpoint = <&hdmi_out_con>;
[all …]
|
| D | sun50i-a64-teres-i.dts | 1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
3 // based on sun50i-a64-olinuxino.dts by Jagan Teki <[email protected]>
5 /dts-v1/;
7 #include "sun50i-a64.dtsi"
8 #include "sun50i-a64-cpu-opp.dtsi"
10 #include <dt-bindings/gpio/gpio.h>
11 #include <dt-bindings/input/input.h>
12 #include <dt-bindings/pwm/pwm.h>
15 model = "Olimex A64 Teres-I";
16 compatible = "olimex,a64-teres-i", "allwinner,sun50i-a64";
[all …]
|
| D | sun50i-h6-tanix.dtsi | 1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
4 /dts-v1/;
6 #include "sun50i-h6.dtsi"
7 #include "sun50i-h6-cpu-opp.dtsi"
9 #include <dt-bindings/gpio/gpio.h>
17 stdout-path = "serial0:115200n8";
21 compatible = "hdmi-connector";
22 ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
27 remote-endpoint = <&hdmi_out_con>;
34 compatible = "i2c-gpio";
[all …]
|
| /linux-6.14.4/Documentation/devicetree/bindings/gpio/ |
| D | gpio-consumer-common.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/gpio/gpio-consumer-common.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Bartosz Golaszewski <[email protected]>
11 - Linus Walleij <[email protected]>
14 Pay attention to using proper GPIO flag (e.g. GPIO_ACTIVE_LOW) for the GPIOs
20 enable-gpios:
25 reset-gpios:
27 GPIO (or GPIOs for power sequence) connected to the device reset pin
[all …]
|
| /linux-6.14.4/arch/arm/mach-pxa/ |
| D | spitz.c | 1 // SPDX-License-Identifier: GPL-2.0-only
3 * Support for Sharp SL-Cxx00 Series of PDAs
4 * Models: SL-C3000 (Spitz), SL-C1000 (Akita) and SL-C3100 (Borzoi)
20 #include <linux/platform_data/i2c-pxa.h>
28 #include <linux/input-event-codes.h>
37 #include <asm/mach-types.h>
43 #include "pxa27x-udc.h"
45 #include <linux/platform_data/mmc-pxamci.h>
46 #include <linux/platform_data/usb-ohci-pxa27x.h>
47 #include <linux/platform_data/video-pxafb.h>
[all …]
|
| /linux-6.14.4/drivers/input/misc/ |
| D | soc_button_array.c | 1 // SPDX-License-Identifier: GPL-2.0-only
23 MODULE_PARM_DESC(use_low_level_irq, "Use low-level triggered IRQ instead of edge triggered");
52 * Some 2-in-1s which use the soc_button_array driver have this ugly issue in
53 * their DSDT where the _LID method modifies the irq-type settings of the GPIOs
57 * problematic because when re-enabling the irq, which happens whenever _LID
59 * irq-type to IRQ_TYPE_LEVEL_LOW. Where as the gpio-keys driver programs the
61 * To work around this we don't set gpio_keys_button.gpio on these 2-in-1s,
69 * Acer Switch 10 SW5-012. _LID method messes with home- and
70 * power-button GPIO IRQ settings. When (re-)enabling the irq
72 * ones, leading to an irq-type of IRQ_TYPE_LEVEL_LOW |
[all …]
|
| /linux-6.14.4/arch/arm64/boot/dts/exynos/google/ |
| D | gs101-oriole.dts | 1 // SPDX-License-Identifier: GPL-2.0-only
5 * Copyright 2021-2023 Google LLC
6 * Copyright 2023 Linaro Ltd - <[email protected]>
9 /dts-v1/;
11 #include <dt-bindings/gpio/gpio.h>
12 #include <dt-bindings/input/input.h>
13 #include <dt-bindings/usb/pd.h>
14 #include "gs101-pinctrl.h"
19 compatible = "google,gs101-oriole", "google,gs101";
28 stdout-path = &serial_0;
[all …]
|
| /linux-6.14.4/arch/arm/boot/dts/nxp/imx/ |
| D | imx6qdl-mba6.dtsi | 1 // SPDX-License-Identifier: GPL-2.0-only
5 * Copyright 2013-2021 TQ-Systems GmbH
6 * Author: Markus Niebel <Markus.Niebel@tq-group.com>
9 #include <dt-bindings/clock/imx6qdl-clock.h>
10 #include <dt-bindings/gpio/gpio.h>
11 #include <dt-bindings/input/input.h>
12 #include <dt-bindings/sound/fsl-imx-audmux.h>
18 /delete-property/ mmc2;
19 /delete-property/ mmc3;
24 stdout-path = &uart2;
[all …]
|
| /linux-6.14.4/Documentation/devicetree/bindings/display/panel/ |
| D | logicpd,type28.yaml | 1 # SPDX-License-Identifier: GPL-2.0
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Logic PD Type 28 4.3" WQVGA TFT LCD panel
10 - Adam Ford <[email protected]>
13 - $ref: panel-common.yaml#
19 power-supply: true
20 enable-gpios: true
25 - compatible
30 - |
[all …]
|
| /linux-6.14.4/drivers/regulator/ |
| D | max8952.c | 1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * max8952.c - Voltage and current regulation for the Maxim 8952
46 int ret = i2c_smbus_read_byte_data(max8952->client, reg); in max8952_read_reg()
57 return i2c_smbus_write_byte_data(max8952->client, reg, value); in max8952_write_reg()
66 return -EINVAL; in max8952_list_voltage()
68 return (max8952->pdata->dvs_mode[selector] * 10 + 770) * 1000; in max8952_list_voltage()
76 if (max8952->vid0) in max8952_get_voltage_sel()
78 if (max8952->vid1) in max8952_get_voltage_sel()
89 if (!max8952->vid0_gpiod || !max8952->vid1_gpiod) { in max8952_set_voltage_sel()
91 return -EPERM; in max8952_set_voltage_sel()
[all …]
|
| /linux-6.14.4/arch/arm/boot/dts/marvell/ |
| D | dove-sbc-a510.dts | 2 * Device Tree file for Compulab SBC-A510 Single Board Computer
6 * This file is dual-licensed: you can use it either under the terms
46 * SBC-A510 comprises a PCA9555 I2C GPIO expander its GPIO lines connected to
51 * 0.3 DVI transmitter TI TFP410 PD# (active low power down)
52 * 0.4 LVDS transmitter DS90C365 PD# (active low power down)
55 * 0.7 mini-PCIe slot W_DISABLE#
67 /dts-v1/;
69 #include "dove-cm-a510.dtsi"
72 model = "Compulab SBC-A510";
73 compatible = "compulab,sbc-a510", "compulab,cm-a510", "marvell,dove";
[all …]
|
| /linux-6.14.4/arch/arm/boot/dts/allwinner/ |
| D | sunxi-d1s-t113-mangopi-mq-r.dtsi | 1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
4 * Common peripherals and configurations for MangoPi MQ-R boards.
7 #include <dt-bindings/gpio/gpio.h>
8 #include <dt-bindings/leds/common.h>
16 stdout-path = "serial3:115200n8";
20 compatible = "gpio-leds";
22 led-0 {
25 gpios = <&pio 3 22 GPIO_ACTIVE_LOW>; /* PD22 */
29 /* board wide 5V supply directly from the USB-C socket */
30 reg_vcc5v: regulator-5v {
[all …]
|
| /linux-6.14.4/arch/arm/boot/dts/ti/omap/ |
| D | am3517-evm-ui.dtsi | 1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (C) 2018 Logic PD, Inc - https://www.logicpd.com/
6 #include <dt-bindings/input/input.h>
10 compatible = "simple-audio-card";
11 simple-audio-card,name = "tlv320aic23-hifi";
13 simple-audio-card,widgets =
18 simple-audio-card,routing =
25 simple-audio-card,format = "i2s";
26 simple-audio-card,bitclock-master = <&sound_master>;
27 simple-audio-card,frame-master = <&sound_master>;
[all …]
|
| /linux-6.14.4/arch/arm64/boot/dts/qcom/ |
| D | sm6115-fxtec-pro1x.dts | 1 // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
3 * Copyright (c) 2023 - 2024, Dang Huynh <[email protected]>
6 /dts-v1/;
11 #include <dt-bindings/arm/qcom,ids.h>
12 #include <dt-bindings/leds/common.h>
13 #include <dt-bindings/usb/pd.h>
18 chassis-type = "handset";
20 qcom,msm-id = <QCOM_ID_SM6115 0x10000>;
23 #address-cells = <2>;
24 #size-cells = <2>;
[all …]
|