Searched full:fan1 (Results 1 – 25 of 62) sorted by relevance
123
| /linux-6.14.4/Documentation/devicetree/bindings/hwmon/ |
| D | maxim,max6639.yaml | 69 fan1: fan-controller@10 {
81 pwms = <&fan1 0 25000 0>;
88 pwms = <&fan1 1 25000 0>;
|
| D | ti,lm87.yaml | 38 in6. Otherwise the pin is set as FAN1 input.
|
| /linux-6.14.4/Documentation/leds/ |
| D | leds-mlxcpld.rst | 14 - mlxcpld:fan1:green
15 - mlxcpld:fan1:red
35 "fan1"
|
| /linux-6.14.4/arch/arm/boot/dts/aspeed/ |
| D | aspeed-bmc-ibm-bonnell.dts | 73 fan1 {
98 fan1-presence {
99 label = "fan1-presence";
137 /*G0-G7*/ "fan0","fan1","","","","","","",
285 fan1: fan@1 { label
|
| D | aspeed-bmc-ufispace-ncplite.dts | 117 fan1-presence {
118 label = "fan1-presence";
275 "","","presence-fan1","",
|
| D | aspeed-bmc-opp-mowgli.dts | 90 event-fan1-presence {
91 label = "fan1-presence";
142 fan1 {
|
| D | aspeed-bmc-opp-witherspoon.dts | 94 event-fan1-presence {
95 label = "fan1-presence";
122 fan1 {
|
| D | aspeed-bmc-opp-swift.dts | 117 event-fan1-presence {
118 label = "fan1-presence";
151 fan1 {
|
| D | aspeed-bmc-ibm-rainier.dts | 142 event-fan1-presence {
143 label = "fan1-presence";
1088 fan1: fan@1 { label
1179 label = "fan1";
|
| /linux-6.14.4/Documentation/hwmon/ |
| D | gl518sm.rst | 51 case when you have selected to turn fan1 off, no fan1 alarm is triggered.
|
| D | w83793.rst | 75 is not controlled by any temp channel, for example, you want to set fan1
112 Only Fan1-5 and PWM1-3 are guaranteed to always exist, other fan inputs and
|
| D | w83795.rst | 61 40 FANIN1 2Eh fan1
117 32 FANIN1 2Eh fan1
|
| D | w83792d.rst | 53 Automatic fan control mode is possible only for fan1-fan3.
83 5 fan1
|
| D | f71805f.rst | 179 Both of the automatic modes require that pwm1 corresponds to fan1, pwm2 to
181 to pwm1 and fan1, etc.
|
| D | w83627ehf.rst | 121 The mode works for fan1-fan4. Mapping of temperatures to pwm outputs is as
236 0x6e only on DHG, CPU fan1 critical temperature
|
| D | asb100.rst | 54 - 0x0040 => fan1
|
| D | lm87.rst | 84 - fan1 (default) or in6
|
| D | mlxreg-fan.rst | 22 fan1 (tacho1) 0xe4
|
| D | f71882fg.rst | 192 All of the automatic modes require that pwm1 corresponds to fan1, pwm2 to
|
| D | dell-smm-hwmon.rst | 154 | | | | | | +------------------- 7. fan1 RPM
156 | | | | +----------------------- 5. fan1 status
|
| /linux-6.14.4/drivers/hwmon/ |
| D | w83792d.c | 107 0x47, /* contains FAN2 and FAN1 Divisor */
147 0x85, /* SmartFanI: Fan1 target value */
153 0x87, /* (bit3-0)SmartFan Fan1 tolerance */
159 { 0x85, /* SmartFanII: Fan1 temp point 1 */
160 0xE3, /* SmartFanII: Fan1 temp point 2 */
161 0xE4, /* SmartFanII: Fan1 temp point 3 */
162 0xE5 }, /* SmartFanII: Fan1 temp point 4 */
174 { 0x88, /* (bit3-0) SmartFanII: Fan1 Non-Stop */
175 0x88, /* (bit7-4) SmartFanII: Fan1 Level 1 */
176 0xE0, /* (bit7-4) SmartFanII: Fan1 Level 2 */
[all …]
|
| D | smsc47m1.c | 714 int fan1, fan2, fan3, pwm1, pwm2, pwm3; in smsc47m1_probe() local
746 fan1 = (smsc47m1_read_value(data, SMSC47M2_REG_TPIN1) in smsc47m1_probe()
755 fan1 = (smsc47m1_read_value(data, SMSC47M1_REG_TPIN(0)) in smsc47m1_probe()
762 if (!(fan1 || fan2 || fan3 || pwm1 || pwm2 || pwm3)) { in smsc47m1_probe()
778 if (fan1) { in smsc47m1_probe()
|
| /linux-6.14.4/drivers/leds/ |
| D | leds-mlxcpld.c | 131 "mlxcpld:fan1:green",
135 "mlxcpld:fan1:red",
|
| /linux-6.14.4/tools/thermal/tmon/ |
| D | tmon.8 | 113 Samples TargetTemp acpitz0 acpitz1 Fan0 Fan1 Fan2 Fan3 Fan4 Fan5
|
| /linux-6.14.4/drivers/platform/mellanox/ |
| D | nvsw-sn2201.c | 428 .label = "fan1",
638 .label = "fan1:green",
643 .label = "fan1:orange",
|
123