Home
last modified time | relevance | path

Searched full:communicates (Results 1 – 25 of 107) sorted by relevance

12345

/linux-6.14.4/drivers/pmdomain/qcom/
DKconfig25 performance states. The driver communicates a performance state
37 performance states. The driver communicates a performance state
/linux-6.14.4/Documentation/virt/
Dne_overview.rst25 primary VM, that communicates with the NE kernel driver via an ioctl interface.
57 An enclave communicates with the primary VM via a local communication channel,
/linux-6.14.4/drivers/virt/acrn/
DKconfig8 communicates with ACRN userspace through ioctls and talks to
/linux-6.14.4/Documentation/devicetree/bindings/sound/
Dti,tas6424.txt3 The TAS6424 serial control bus communicates through I2C protocols.
Dtas5720.txt3 The TAS5720 serial control bus communicates through the I2C protocol only. The
Dtas2552.txt3 The tas2552 serial control bus communicates through I2C protocols
/linux-6.14.4/Documentation/ABI/testing/
Dsysfs-bus-platform-devices-occ-hwmon10 a Baseboard Management Controller (BMC), communicates with
/linux-6.14.4/Documentation/hwmon/
Dpowerz.rst24 The device communicates with the custom protocol over USB.
Dhs3001.rst28 The device communicates with the I2C protocol. Sensors have the I2C
Dshtc1.rst47 The device communicates with the I2C protocol. All sensors are set to I2C
Dlm70.rst41 It communicates with a host processor (or microcontroller) via an
Dsht4x.rst32 The device communicates with the I2C protocol. Sensors can have the I2C
Dpli1209bc.rst24 (BCM). The PLI communicates with a system controller via a PMBus compatible
/linux-6.14.4/arch/arm/boot/dts/broadcom/
Dbcm283x-rpi-wifi-bt.dtsi26 /* uart0 communicates with the BT module */
Dbcm2711-rpi-cm4.dtsi97 /* uart0 communicates with the BT module */
Dbcm2837-rpi-3-b-plus.dts148 /* uart0 communicates with the BT module */
Dbcm2837-rpi-3-a-plus.dts142 /* uart0 communicates with the BT module
/linux-6.14.4/drivers/ufs/core/
DKconfig18 A UFS controller communicates with a UFS device by exchanging
/linux-6.14.4/Documentation/devicetree/bindings/mfd/
Dzii,rave-sp.yaml13 RAVE Supervisory Processor communicates with SoC over UART. It is
/linux-6.14.4/Documentation/devicetree/bindings/tpm/
Dgoogle,cr50.yaml18 It communicates over SPI or I²C using the FIFO protocol described in the
/linux-6.14.4/Documentation/devicetree/bindings/leds/
Dcznic,turris-omnia-leds.yaml15 microcontroller that communicates via the I2C bus. Each LED is described
/linux-6.14.4/drivers/phy/ti/
DKconfig73 The USB OTG controller communicates with the comparator using this
/linux-6.14.4/Documentation/virt/hyperv/
Dhibernation.rst150 re-opens the existing channel. It then communicates with Hyper-V to
185 device re-opens its primary channel, and communicates with Hyper-V
258 operating and communicates to Hyper-V that it is prepared to accept a
/linux-6.14.4/Documentation/leds/
Dleds-lp5521.rst52 The test communicates with the chip and checks that
/linux-6.14.4/Documentation/infiniband/
Duser_verbs.rst20 Userspace communicates with the kernel for slow path, resource

12345