1 /** 2 ****************************************************************************** 3 * @file stm32f4xx_hal_conf_template.h 4 * @author MCD Application Team 5 * @brief HAL configuration template file. 6 * This file should be copied to the application folder and renamed 7 * to stm32f4xx_hal_conf.h. 8 ****************************************************************************** 9 * @attention 10 * 11 * <h2><center>© Copyright (c) 2017 STMicroelectronics. 12 * All rights reserved.</center></h2> 13 * 14 * This software component is licensed by ST under BSD 3-Clause license, 15 * the "License"; You may not use this file except in compliance with the 16 * License. You may obtain a copy of the License at: 17 * opensource.org/licenses/BSD-3-Clause 18 * 19 ****************************************************************************** 20 */ 21 22 /* Define to prevent recursive inclusion -------------------------------------*/ 23 #ifndef __STM32F4xx_HAL_CONF_H 24 #define __STM32F4xx_HAL_CONF_H 25 26 #ifdef __cplusplus 27 extern "C" { 28 #endif 29 30 /* Exported types ------------------------------------------------------------*/ 31 /* Exported constants --------------------------------------------------------*/ 32 33 /* ########################## Module Selection ############################## */ 34 /** 35 * @brief This is the list of modules to be used in the HAL driver 36 */ 37 #define HAL_MODULE_ENABLED 38 #define HAL_ADC_MODULE_ENABLED 39 #define HAL_CAN_MODULE_ENABLED 40 /* #define HAL_CAN_LEGACY_MODULE_ENABLED */ 41 #define HAL_CRC_MODULE_ENABLED 42 #define HAL_CEC_MODULE_ENABLED 43 #define HAL_CRYP_MODULE_ENABLED 44 #define HAL_DAC_MODULE_ENABLED 45 #define HAL_DCMI_MODULE_ENABLED 46 #define HAL_DMA_MODULE_ENABLED 47 #define HAL_DMA2D_MODULE_ENABLED 48 #define HAL_ETH_MODULE_ENABLED 49 #define HAL_FLASH_MODULE_ENABLED 50 #define HAL_NAND_MODULE_ENABLED 51 #define HAL_NOR_MODULE_ENABLED 52 #define HAL_PCCARD_MODULE_ENABLED 53 #define HAL_SRAM_MODULE_ENABLED 54 #define HAL_SDRAM_MODULE_ENABLED 55 #define HAL_HASH_MODULE_ENABLED 56 #define HAL_GPIO_MODULE_ENABLED 57 #define HAL_EXTI_MODULE_ENABLED 58 #define HAL_I2C_MODULE_ENABLED 59 #define HAL_SMBUS_MODULE_ENABLED 60 #define HAL_I2S_MODULE_ENABLED 61 #define HAL_IWDG_MODULE_ENABLED 62 #define HAL_LTDC_MODULE_ENABLED 63 #define HAL_DSI_MODULE_ENABLED 64 #define HAL_PWR_MODULE_ENABLED 65 #define HAL_QSPI_MODULE_ENABLED 66 #define HAL_RCC_MODULE_ENABLED 67 #define HAL_RNG_MODULE_ENABLED 68 #define HAL_RTC_MODULE_ENABLED 69 #define HAL_SAI_MODULE_ENABLED 70 #define HAL_SD_MODULE_ENABLED 71 #define HAL_SPI_MODULE_ENABLED 72 #define HAL_TIM_MODULE_ENABLED 73 #define HAL_UART_MODULE_ENABLED 74 #define HAL_USART_MODULE_ENABLED 75 #define HAL_IRDA_MODULE_ENABLED 76 #define HAL_SMARTCARD_MODULE_ENABLED 77 #define HAL_WWDG_MODULE_ENABLED 78 #define HAL_CORTEX_MODULE_ENABLED 79 #define HAL_PCD_MODULE_ENABLED 80 #define HAL_HCD_MODULE_ENABLED 81 #define HAL_FMPI2C_MODULE_ENABLED 82 #define HAL_SPDIFRX_MODULE_ENABLED 83 #define HAL_DFSDM_MODULE_ENABLED 84 #define HAL_LPTIM_MODULE_ENABLED 85 #define HAL_MMC_MODULE_ENABLED 86 87 /* ########################## HSE/HSI Values adaptation ##################### */ 88 /** 89 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. 90 * This value is used by the RCC HAL module to compute the system frequency 91 * (when HSE is used as system clock source, directly or through the PLL). 92 */ 93 #if !defined (HSE_VALUE) 94 #define HSE_VALUE 25000000U /*!< Value of the External oscillator in Hz */ 95 #endif /* HSE_VALUE */ 96 97 #if !defined (HSE_STARTUP_TIMEOUT) 98 #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */ 99 #endif /* HSE_STARTUP_TIMEOUT */ 100 101 /** 102 * @brief Internal High Speed oscillator (HSI) value. 103 * This value is used by the RCC HAL module to compute the system frequency 104 * (when HSI is used as system clock source, directly or through the PLL). 105 */ 106 #if !defined (HSI_VALUE) 107 #define HSI_VALUE 16000000U /*!< Value of the Internal oscillator in Hz */ 108 #endif /* HSI_VALUE */ 109 110 /** 111 * @brief Internal Low Speed oscillator (LSI) value. 112 */ 113 #if !defined (LSI_VALUE) 114 #define LSI_VALUE 32000U /*!< LSI Typical Value in Hz */ 115 #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz 116 The real value may vary depending on the variations 117 in voltage and temperature. */ 118 /** 119 * @brief External Low Speed oscillator (LSE) value. 120 */ 121 #if !defined (LSE_VALUE) 122 #define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */ 123 #endif /* LSE_VALUE */ 124 125 #if !defined (LSE_STARTUP_TIMEOUT) 126 #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ 127 #endif /* LSE_STARTUP_TIMEOUT */ 128 129 /** 130 * @brief External clock source for I2S peripheral 131 * This value is used by the I2S HAL module to compute the I2S clock source 132 * frequency, this source is inserted directly through I2S_CKIN pad. 133 */ 134 #if !defined (EXTERNAL_CLOCK_VALUE) 135 #define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the External oscillator in Hz*/ 136 #endif /* EXTERNAL_CLOCK_VALUE */ 137 138 /* Tip: To avoid modifying this file each time you need to use different HSE, 139 === you can define the HSE value in your toolchain compiler preprocessor. */ 140 141 /* ########################### System Configuration ######################### */ 142 /** 143 * @brief This is the HAL system configuration section 144 */ 145 #define VDD_VALUE 3300U /*!< Value of VDD in mv */ 146 #define TICK_INT_PRIORITY 0x0FU /*!< tick interrupt priority */ 147 #define USE_RTOS 0U 148 #define PREFETCH_ENABLE 1U 149 #define INSTRUCTION_CACHE_ENABLE 1U 150 #define DATA_CACHE_ENABLE 1U 151 152 #define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ 153 #define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ 154 #define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ 155 #define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */ 156 #define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ 157 #define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */ 158 #define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */ 159 #define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */ 160 #define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */ 161 #define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ 162 #define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */ 163 #define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ 164 #define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ 165 #define USE_HAL_FMPI2C_REGISTER_CALLBACKS 0U /* FMPI2C register callback disabled */ 166 #define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ 167 #define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ 168 #define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */ 169 #define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */ 170 #define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ 171 #define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ 172 #define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ 173 #define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */ 174 #define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ 175 #define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */ 176 #define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */ 177 #define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ 178 #define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */ 179 #define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ 180 #define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ 181 #define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */ 182 #define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ 183 #define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */ 184 #define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */ 185 #define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ 186 #define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ 187 #define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ 188 #define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ 189 #define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ 190 191 /* ########################## Assert Selection ############################## */ 192 /** 193 * @brief Uncomment the line below to expanse the "assert_param" macro in the 194 * HAL drivers code 195 */ 196 /* #define USE_FULL_ASSERT 1U */ 197 198 /* ################## Ethernet peripheral configuration ##################### */ 199 200 /* Section 1 : Ethernet peripheral configuration */ 201 202 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ 203 #define MAC_ADDR0 2U 204 #define MAC_ADDR1 0U 205 #define MAC_ADDR2 0U 206 #define MAC_ADDR3 0U 207 #define MAC_ADDR4 0U 208 #define MAC_ADDR5 0U 209 210 /* Definition of the Ethernet driver buffers size and count */ 211 #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ 212 #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ 213 #define ETH_RXBUFNB 4U /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ 214 #define ETH_TXBUFNB 4U /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ 215 216 /* Section 2: PHY configuration section */ 217 218 /* DP83848 PHY Address*/ 219 #define DP83848_PHY_ADDRESS 0x01U 220 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ 221 #define PHY_RESET_DELAY 0x000000FFU 222 /* PHY Configuration delay */ 223 #define PHY_CONFIG_DELAY 0x00000FFFU 224 225 #define PHY_READ_TO 0x0000FFFFU 226 #define PHY_WRITE_TO 0x0000FFFFU 227 228 /* Section 3: Common PHY Registers */ 229 230 #define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */ 231 #define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */ 232 233 #define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ 234 #define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ 235 #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ 236 #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ 237 #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ 238 #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ 239 #define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ 240 #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ 241 #define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ 242 #define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ 243 244 #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ 245 #define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ 246 #define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ 247 248 /* Section 4: Extended PHY Registers */ 249 250 #define PHY_SR ((uint16_t)0x0010) /*!< PHY status register Offset */ 251 #define PHY_MICR ((uint16_t)0x0011) /*!< MII Interrupt Control Register */ 252 #define PHY_MISR ((uint16_t)0x0012) /*!< MII Interrupt Status and Misc. Control Register */ 253 254 #define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */ 255 #define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */ 256 #define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */ 257 258 #define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */ 259 #define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */ 260 261 #define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */ 262 #define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */ 263 264 /* ################## SPI peripheral configuration ########################## */ 265 266 /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver 267 * Activated: CRC code is present inside driver 268 * Deactivated: CRC code cleaned from driver 269 */ 270 271 #define USE_SPI_CRC 1U 272 273 /* Includes ------------------------------------------------------------------*/ 274 /** 275 * @brief Include module's header file 276 */ 277 278 #ifdef HAL_RCC_MODULE_ENABLED 279 #include "stm32f4xx_hal_rcc.h" 280 #endif /* HAL_RCC_MODULE_ENABLED */ 281 282 #ifdef HAL_GPIO_MODULE_ENABLED 283 #include "stm32f4xx_hal_gpio.h" 284 #endif /* HAL_GPIO_MODULE_ENABLED */ 285 286 #ifdef HAL_EXTI_MODULE_ENABLED 287 #include "stm32f4xx_hal_exti.h" 288 #endif /* HAL_EXTI_MODULE_ENABLED */ 289 290 #ifdef HAL_DMA_MODULE_ENABLED 291 #include "stm32f4xx_hal_dma.h" 292 #endif /* HAL_DMA_MODULE_ENABLED */ 293 294 #ifdef HAL_CORTEX_MODULE_ENABLED 295 #include "stm32f4xx_hal_cortex.h" 296 #endif /* HAL_CORTEX_MODULE_ENABLED */ 297 298 #ifdef HAL_ADC_MODULE_ENABLED 299 #include "stm32f4xx_hal_adc.h" 300 #endif /* HAL_ADC_MODULE_ENABLED */ 301 302 #ifdef HAL_CAN_MODULE_ENABLED 303 #include "stm32f4xx_hal_can.h" 304 #endif /* HAL_CAN_MODULE_ENABLED */ 305 306 #ifdef HAL_CAN_LEGACY_MODULE_ENABLED 307 #include "stm32f4xx_hal_can_legacy.h" 308 #endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ 309 310 #ifdef HAL_CRC_MODULE_ENABLED 311 #include "stm32f4xx_hal_crc.h" 312 #endif /* HAL_CRC_MODULE_ENABLED */ 313 314 #ifdef HAL_CRYP_MODULE_ENABLED 315 #include "stm32f4xx_hal_cryp.h" 316 #endif /* HAL_CRYP_MODULE_ENABLED */ 317 318 #ifdef HAL_DMA2D_MODULE_ENABLED 319 #include "stm32f4xx_hal_dma2d.h" 320 #endif /* HAL_DMA2D_MODULE_ENABLED */ 321 322 #ifdef HAL_DAC_MODULE_ENABLED 323 #include "stm32f4xx_hal_dac.h" 324 #endif /* HAL_DAC_MODULE_ENABLED */ 325 326 #ifdef HAL_DCMI_MODULE_ENABLED 327 #include "stm32f4xx_hal_dcmi.h" 328 #endif /* HAL_DCMI_MODULE_ENABLED */ 329 330 #ifdef HAL_ETH_MODULE_ENABLED 331 #include "stm32f4xx_hal_eth.h" 332 #endif /* HAL_ETH_MODULE_ENABLED */ 333 334 #ifdef HAL_FLASH_MODULE_ENABLED 335 #include "stm32f4xx_hal_flash.h" 336 #endif /* HAL_FLASH_MODULE_ENABLED */ 337 338 #ifdef HAL_SRAM_MODULE_ENABLED 339 #include "stm32f4xx_hal_sram.h" 340 #endif /* HAL_SRAM_MODULE_ENABLED */ 341 342 #ifdef HAL_NOR_MODULE_ENABLED 343 #include "stm32f4xx_hal_nor.h" 344 #endif /* HAL_NOR_MODULE_ENABLED */ 345 346 #ifdef HAL_NAND_MODULE_ENABLED 347 #include "stm32f4xx_hal_nand.h" 348 #endif /* HAL_NAND_MODULE_ENABLED */ 349 350 #ifdef HAL_PCCARD_MODULE_ENABLED 351 #include "stm32f4xx_hal_pccard.h" 352 #endif /* HAL_PCCARD_MODULE_ENABLED */ 353 354 #ifdef HAL_SDRAM_MODULE_ENABLED 355 #include "stm32f4xx_hal_sdram.h" 356 #endif /* HAL_SDRAM_MODULE_ENABLED */ 357 358 #ifdef HAL_HASH_MODULE_ENABLED 359 #include "stm32f4xx_hal_hash.h" 360 #endif /* HAL_HASH_MODULE_ENABLED */ 361 362 #ifdef HAL_I2C_MODULE_ENABLED 363 #include "stm32f4xx_hal_i2c.h" 364 #endif /* HAL_I2C_MODULE_ENABLED */ 365 366 #ifdef HAL_SMBUS_MODULE_ENABLED 367 #include "stm32f4xx_hal_smbus.h" 368 #endif /* HAL_SMBUS_MODULE_ENABLED */ 369 370 #ifdef HAL_I2S_MODULE_ENABLED 371 #include "stm32f4xx_hal_i2s.h" 372 #endif /* HAL_I2S_MODULE_ENABLED */ 373 374 #ifdef HAL_IWDG_MODULE_ENABLED 375 #include "stm32f4xx_hal_iwdg.h" 376 #endif /* HAL_IWDG_MODULE_ENABLED */ 377 378 #ifdef HAL_LTDC_MODULE_ENABLED 379 #include "stm32f4xx_hal_ltdc.h" 380 #endif /* HAL_LTDC_MODULE_ENABLED */ 381 382 #ifdef HAL_PWR_MODULE_ENABLED 383 #include "stm32f4xx_hal_pwr.h" 384 #endif /* HAL_PWR_MODULE_ENABLED */ 385 386 #ifdef HAL_RNG_MODULE_ENABLED 387 #include "stm32f4xx_hal_rng.h" 388 #endif /* HAL_RNG_MODULE_ENABLED */ 389 390 #ifdef HAL_RTC_MODULE_ENABLED 391 #include "stm32f4xx_hal_rtc.h" 392 #endif /* HAL_RTC_MODULE_ENABLED */ 393 394 #ifdef HAL_SAI_MODULE_ENABLED 395 #include "stm32f4xx_hal_sai.h" 396 #endif /* HAL_SAI_MODULE_ENABLED */ 397 398 #ifdef HAL_SD_MODULE_ENABLED 399 #include "stm32f4xx_hal_sd.h" 400 #endif /* HAL_SD_MODULE_ENABLED */ 401 402 #ifdef HAL_SPI_MODULE_ENABLED 403 #include "stm32f4xx_hal_spi.h" 404 #endif /* HAL_SPI_MODULE_ENABLED */ 405 406 #ifdef HAL_TIM_MODULE_ENABLED 407 #include "stm32f4xx_hal_tim.h" 408 #endif /* HAL_TIM_MODULE_ENABLED */ 409 410 #ifdef HAL_UART_MODULE_ENABLED 411 #include "stm32f4xx_hal_uart.h" 412 #endif /* HAL_UART_MODULE_ENABLED */ 413 414 #ifdef HAL_USART_MODULE_ENABLED 415 #include "stm32f4xx_hal_usart.h" 416 #endif /* HAL_USART_MODULE_ENABLED */ 417 418 #ifdef HAL_IRDA_MODULE_ENABLED 419 #include "stm32f4xx_hal_irda.h" 420 #endif /* HAL_IRDA_MODULE_ENABLED */ 421 422 #ifdef HAL_SMARTCARD_MODULE_ENABLED 423 #include "stm32f4xx_hal_smartcard.h" 424 #endif /* HAL_SMARTCARD_MODULE_ENABLED */ 425 426 #ifdef HAL_WWDG_MODULE_ENABLED 427 #include "stm32f4xx_hal_wwdg.h" 428 #endif /* HAL_WWDG_MODULE_ENABLED */ 429 430 #ifdef HAL_PCD_MODULE_ENABLED 431 #include "stm32f4xx_hal_pcd.h" 432 #endif /* HAL_PCD_MODULE_ENABLED */ 433 434 #ifdef HAL_HCD_MODULE_ENABLED 435 #include "stm32f4xx_hal_hcd.h" 436 #endif /* HAL_HCD_MODULE_ENABLED */ 437 438 #ifdef HAL_DSI_MODULE_ENABLED 439 #include "stm32f4xx_hal_dsi.h" 440 #endif /* HAL_DSI_MODULE_ENABLED */ 441 442 #ifdef HAL_QSPI_MODULE_ENABLED 443 #include "stm32f4xx_hal_qspi.h" 444 #endif /* HAL_QSPI_MODULE_ENABLED */ 445 446 #ifdef HAL_CEC_MODULE_ENABLED 447 #include "stm32f4xx_hal_cec.h" 448 #endif /* HAL_CEC_MODULE_ENABLED */ 449 450 #ifdef HAL_FMPI2C_MODULE_ENABLED 451 #include "stm32f4xx_hal_fmpi2c.h" 452 #endif /* HAL_FMPI2C_MODULE_ENABLED */ 453 454 #ifdef HAL_SPDIFRX_MODULE_ENABLED 455 #include "stm32f4xx_hal_spdifrx.h" 456 #endif /* HAL_SPDIFRX_MODULE_ENABLED */ 457 458 #ifdef HAL_DFSDM_MODULE_ENABLED 459 #include "stm32f4xx_hal_dfsdm.h" 460 #endif /* HAL_DFSDM_MODULE_ENABLED */ 461 462 #ifdef HAL_LPTIM_MODULE_ENABLED 463 #include "stm32f4xx_hal_lptim.h" 464 #endif /* HAL_LPTIM_MODULE_ENABLED */ 465 466 #ifdef HAL_MMC_MODULE_ENABLED 467 #include "stm32f4xx_hal_mmc.h" 468 #endif /* HAL_MMC_MODULE_ENABLED */ 469 470 /* Exported macro ------------------------------------------------------------*/ 471 #ifdef USE_FULL_ASSERT 472 /** 473 * @brief The assert_param macro is used for function's parameters check. 474 * @param expr If expr is false, it calls assert_failed function 475 * which reports the name of the source file and the source 476 * line number of the call that failed. 477 * If expr is true, it returns no value. 478 * @retval None 479 */ 480 #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) 481 /* Exported functions ------------------------------------------------------- */ 482 void assert_failed(uint8_t* file, uint32_t line); 483 #else 484 #define assert_param(expr) ((void)0U) 485 #endif /* USE_FULL_ASSERT */ 486 487 488 #ifdef __cplusplus 489 } 490 #endif 491 492 #endif /* __STM32F4xx_HAL_CONF_H */ 493 494 495 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ 496