62  * 2) Make sure we check incoming data packets for size and all that. You
106  * 2) I think one way to handle the problem of losing up to a microsecond
229  * and we are currently at 1Mbps or lower data rate and we could use
527         /* Upper 6 bits must have 2 transitions */  in ble_ll_conn_calc_access_addr()
1002      * 2) We successfully sent the reject reason.  in ble_ll_conn_chk_csm_flags()
1544              * 2) The address rx time and jitter is accounted for in the  in ble_ll_conn_event_start_cb()
1548                 (2 * connsm->slave_cur_window_widening);  in ble_ll_conn_event_start_cb()
1629         usecs += (BLE_LL_IFS * 2) + connsm->eff_max_rx_time;  in ble_ll_conn_can_send_next_pdu()
1758     if (hcc->min_ce_len > (connsm->conn_itvl * 2)) {  in ble_ll_conn_master_init()
1759         connsm->min_ce_len = connsm->conn_itvl * 2;  in ble_ll_conn_master_init()
1764     if (hcc->max_ce_len > (connsm->conn_itvl * 2)) {  in ble_ll_conn_master_init()
1765         connsm->max_ce_len = connsm->conn_itvl * 2;  in ble_ll_conn_master_init()
1873     if (hcc_params->min_ce_len > (connsm->conn_itvl * 2)) {  in ble_ll_conn_ext_set_params()
1874         connsm->min_ce_len = connsm->conn_itvl * 2;  in ble_ll_conn_ext_set_params()
1879     if (hcc_params->max_ce_len > (connsm->conn_itvl * 2)) {  in ble_ll_conn_ext_set_params()
1880         connsm->max_ce_len = connsm->conn_itvl * 2;  in ble_ll_conn_ext_set_params()
2383         max_ww = (connsm->conn_itvl * (BLE_LL_CONN_ITVL_USECS/2)) - BLE_LL_IFS;  in ble_ll_conn_next_event()
2404  *  See Section 4.5.2 Vol 6 Part B
2651      * 2) We may end the supervision timeout a bit later than specified as  in ble_ll_conn_event_end()
3022                 addr_type = g_ble_ll_resolv_list[rpa_index].rl_addr_type + 2;  in ble_ll_init_rx_pkt_in()
3151     dptr += (2 * BLE_DEV_ADDR_LEN);  in ble_ll_conn_req_pdu_make()
3723                     BLE_LL_ASSERT(OS_MBUF_LEADINGSPACE(rxpdu) >= 2);  in ble_ll_conn_rx_data_pdu()
3724                     os_mbuf_prepend(rxpdu, 2);  in ble_ll_conn_rx_data_pdu()
3729                     put_le16(rxbuf + 2, acl_len);  in ble_ll_conn_rx_data_pdu()
3832         if (connsm->cons_rxd_bad_crc >= 2) {  in ble_ll_conn_rx_isr_end()
3866             opcode = rxbuf[2];  in ble_ll_conn_rx_isr_end()
3942                             if (connsm->completed_pkts > 2) {  in ble_ll_conn_rx_isr_end()
4252     temp = (connsm->slave_latency + 1) * (connsm->conn_itvl * 2) *  in ble_ll_conn_slave_start()
4276     if (connsm->num_used_chans < 2) {  in ble_ll_conn_slave_start()