Lines Matching +full:high +full:- +full:frequency

8 // <e> NRFX_CLOCK_ENABLED - nrfx_clock - CLOCK peripheral driver
13 // <o> NRFX_CLOCK_CONFIG_LF_SRC  - LF Clock Source
25 // <q> NRFX_CLOCK_CONFIG_LF_CAL_ENABLED  - Enables LF Clock Calibration Support
31 // <o> NRFX_CLOCK_CONFIG_IRQ_PRIORITY  - Interrupt priority
46 // <e> NRFX_CLOCK_CONFIG_LOG_ENABLED - Enables logging in the module.
51 // <o> NRFX_CLOCK_CONFIG_LOG_LEVEL  - Default Severity level
63 // <o> NRFX_CLOCK_CONFIG_INFO_COLOR  - ANSI escape code prefix.
79 // <o> NRFX_CLOCK_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
99 // <e> NRFX_COMP_ENABLED - nrfx_comp - COMP peripheral driver
104 // <o> NRFX_COMP_CONFIG_REF  - Reference voltage
116 // <o> NRFX_COMP_CONFIG_MAIN_MODE  - Main mode
125 // <o> NRFX_COMP_CONFIG_SPEED_MODE  - Speed mode
129 // <2=> High speed
135 // <o> NRFX_COMP_CONFIG_HYST  - Hystheresis
144 // <o> NRFX_COMP_CONFIG_ISOURCE  - Current Source
155 // <o> NRFX_COMP_CONFIG_INPUT  - Analog input
170 // <o> NRFX_COMP_CONFIG_IRQ_PRIORITY  - Interrupt priority
185 // <e> NRFX_COMP_CONFIG_LOG_ENABLED - Enables logging in the module.
190 // <o> NRFX_COMP_CONFIG_LOG_LEVEL  - Default Severity level
202 // <o> NRFX_COMP_CONFIG_INFO_COLOR  - ANSI escape code prefix.
218 // <o> NRFX_COMP_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
238 // <e> NRFX_GPIOTE_ENABLED - nrfx_gpiote - GPIOTE peripheral driver
243 // <o> NRFX_GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS - Number of lower power input pins
248 // <o> NRFX_GPIOTE_CONFIG_IRQ_PRIORITY  - Interrupt priority
263 // <e> NRFX_GPIOTE_CONFIG_LOG_ENABLED - Enables logging in the module.
268 // <o> NRFX_GPIOTE_CONFIG_LOG_LEVEL  - Default Severity level
280 // <o> NRFX_GPIOTE_CONFIG_INFO_COLOR  - ANSI escape code prefix.
296 // <o> NRFX_GPIOTE_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
316 // <e> NRFX_I2S_ENABLED - nrfx_i2s - I2S peripheral driver
321 // <o> NRFX_I2S_CONFIG_SCK_PIN - SCK pin  <0-31>
328 // <o> NRFX_I2S_CONFIG_LRCK_PIN - LRCK pin  <1-31>
335 // <o> NRFX_I2S_CONFIG_MCK_PIN - MCK pin
340 // <o> NRFX_I2S_CONFIG_SDOUT_PIN - SDOUT pin  <0-31>
347 // <o> NRFX_I2S_CONFIG_SDIN_PIN - SDIN pin  <0-31>
354 // <o> NRFX_I2S_CONFIG_MASTER  - Mode
363 // <o> NRFX_I2S_CONFIG_FORMAT  - Format
372 // <o> NRFX_I2S_CONFIG_ALIGN  - Alignment
381 // <o> NRFX_I2S_CONFIG_SWIDTH  - Sample width (bits)
391 // <o> NRFX_I2S_CONFIG_CHANNELS  - Channels
401 // <o> NRFX_I2S_CONFIG_MCK_SETUP  - MCK behavior
427 // <o> NRFX_I2S_CONFIG_RATIO  - MCK/LRCK ratio
443 // <o> NRFX_I2S_CONFIG_IRQ_PRIORITY  - Interrupt priority
458 // <e> NRFX_I2S_CONFIG_LOG_ENABLED - Enables logging in the module.
463 // <o> NRFX_I2S_CONFIG_LOG_LEVEL  - Default Severity level
475 // <o> NRFX_I2S_CONFIG_INFO_COLOR  - ANSI escape code prefix.
491 // <o> NRFX_I2S_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
511 // <e> NRFX_LPCOMP_ENABLED - nrfx_lpcomp - LPCOMP peripheral driver
516 // <o> NRFX_LPCOMP_CONFIG_REFERENCE  - Reference voltage
540 // <o> NRFX_LPCOMP_CONFIG_DETECTION  - Detection
550 // <o> NRFX_LPCOMP_CONFIG_INPUT  - Analog input
565 // <q> NRFX_LPCOMP_CONFIG_HYST  - Hysteresis
572 // <o> NRFX_LPCOMP_CONFIG_IRQ_PRIORITY  - Interrupt priority
587 // <e> NRFX_LPCOMP_CONFIG_LOG_ENABLED - Enables logging in the module.
592 // <o> NRFX_LPCOMP_CONFIG_LOG_LEVEL  - Default Severity level
604 // <o> NRFX_LPCOMP_CONFIG_INFO_COLOR  - ANSI escape code prefix.
620 // <o> NRFX_LPCOMP_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
640 // <e> NRFX_NFCT_ENABLED - nrfx_nfct - NFCT peripheral driver
645 // <o> NRFX_NFCT_CONFIG_IRQ_PRIORITY  - Interrupt priority
660 // <e> NRFX_NFCT_CONFIG_LOG_ENABLED - Enables logging in the module.
665 // <o> NRFX_NFCT_CONFIG_LOG_LEVEL  - Default Severity level
677 // <o> NRFX_NFCT_CONFIG_INFO_COLOR  - ANSI escape code prefix.
693 // <o> NRFX_NFCT_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
713 // <e> NRFX_PDM_ENABLED - nrfx_pdm - PDM peripheral driver
718 // <o> NRFX_PDM_CONFIG_MODE  - Mode
727 // <o> NRFX_PDM_CONFIG_EDGE  - Edge
736 // <o> NRFX_PDM_CONFIG_CLOCK_FREQ  - Clock frequency
746 // <o> NRFX_PDM_CONFIG_IRQ_PRIORITY  - Interrupt priority
761 // <e> NRFX_PDM_CONFIG_LOG_ENABLED - Enables logging in the module.
766 // <o> NRFX_PDM_CONFIG_LOG_LEVEL  - Default Severity level
778 // <o> NRFX_PDM_CONFIG_INFO_COLOR  - ANSI escape code prefix.
794 // <o> NRFX_PDM_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
814 // <e> NRFX_POWER_ENABLED - nrfx_power - POWER peripheral driver
819 // <o> NRFX_POWER_CONFIG_IRQ_PRIORITY  - Interrupt priority
834 // <q> NRFX_POWER_CONFIG_DEFAULT_DCDCEN  - The default configuration of main DCDC regulator
843 // <q> NRFX_POWER_CONFIG_DEFAULT_DCDCENHV  - The default configuration of High Voltage DCDC regulat…
854 // <e> NRFX_PPI_ENABLED - nrfx_ppi - PPI peripheral allocator
859 // <e> NRFX_PPI_CONFIG_LOG_ENABLED - Enables logging in the module.
864 // <o> NRFX_PPI_CONFIG_LOG_LEVEL  - Default Severity level
876 // <o> NRFX_PPI_CONFIG_INFO_COLOR  - ANSI escape code prefix.
892 // <o> NRFX_PPI_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
912 // <e> NRFX_PRS_ENABLED - nrfx_prs - Peripheral Resource Sharing module
917 // <q> NRFX_PRS_BOX_0_ENABLED  - Enables box 0 in the module.
924 // <q> NRFX_PRS_BOX_1_ENABLED  - Enables box 1 in the module.
931 // <q> NRFX_PRS_BOX_2_ENABLED  - Enables box 2 in the module.
938 // <q> NRFX_PRS_BOX_3_ENABLED  - Enables box 3 in the module.
945 // <q> NRFX_PRS_BOX_4_ENABLED  - Enables box 4 in the module.
952 // <e> NRFX_PRS_CONFIG_LOG_ENABLED - Enables logging in the module.
957 // <o> NRFX_PRS_CONFIG_LOG_LEVEL  - Default Severity level
969 // <o> NRFX_PRS_CONFIG_INFO_COLOR  - ANSI escape code prefix.
985 // <o> NRFX_PRS_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
1005 // <e> NRFX_PWM_ENABLED - nrfx_pwm - PWM peripheral driver
1010 // <q> NRFX_PWM0_ENABLED  - Enable PWM0 instance
1017 // <q> NRFX_PWM1_ENABLED  - Enable PWM1 instance
1024 // <q> NRFX_PWM2_ENABLED  - Enable PWM2 instance
1031 // <o> NRFX_PWM_DEFAULT_CONFIG_OUT0_PIN - Out0 pin  <0-31>
1038 // <o> NRFX_PWM_DEFAULT_CONFIG_OUT1_PIN - Out1 pin  <0-31>
1045 // <o> NRFX_PWM_DEFAULT_CONFIG_OUT2_PIN - Out2 pin  <0-31>
1052 // <o> NRFX_PWM_DEFAULT_CONFIG_OUT3_PIN - Out3 pin  <0-31>
1059 // <o> NRFX_PWM_DEFAULT_CONFIG_BASE_CLOCK  - Base clock
1074 // <o> NRFX_PWM_DEFAULT_CONFIG_COUNT_MODE  - Count mode
1083 // <o> NRFX_PWM_DEFAULT_CONFIG_TOP_VALUE - Top value
1088 // <o> NRFX_PWM_DEFAULT_CONFIG_LOAD_MODE  - Load mode
1099 // <o> NRFX_PWM_DEFAULT_CONFIG_STEP_MODE  - Step mode
1108 // <o> NRFX_PWM_DEFAULT_CONFIG_IRQ_PRIORITY  - Interrupt priority
1123 // <e> NRFX_PWM_CONFIG_LOG_ENABLED - Enables logging in the module.
1128 // <o> NRFX_PWM_CONFIG_LOG_LEVEL  - Default Severity level
1140 // <o> NRFX_PWM_CONFIG_INFO_COLOR  - ANSI escape code prefix.
1156 // <o> NRFX_PWM_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
1174 // <e> NRFX_PWM_NRF52_ANOMALY_109_WORKAROUND_ENABLED - Enables nRF52 Anomaly 109 workaround for PWM.
1187 // <o> NRFX_PWM_NRF52_ANOMALY_109_EGU_INSTANCE  - EGU instance used by the nRF52 Anomaly 109 workar…
1204 // <e> NRFX_QDEC_ENABLED - nrfx_qdec - QDEC peripheral driver
1209 // <o> NRFX_QDEC_CONFIG_REPORTPER  - Report period
1224 // <o> NRFX_QDEC_CONFIG_SAMPLEPER  - Sample period
1239 // <o> NRFX_QDEC_CONFIG_PIO_A - A pin  <0-31>
1246 // <o> NRFX_QDEC_CONFIG_PIO_B - B pin  <0-31>
1253 // <o> NRFX_QDEC_CONFIG_PIO_LED - LED pin  <0-31>
1260 // <o> NRFX_QDEC_CONFIG_LEDPRE - LED pre
1265 // <o> NRFX_QDEC_CONFIG_LEDPOL  - LED polarity
1268 // <1=> Active high
1274 // <q> NRFX_QDEC_CONFIG_DBFEN  - Debouncing enable
1281 // <q> NRFX_QDEC_CONFIG_SAMPLE_INTEN  - Sample ready interrupt enable
1288 // <o> NRFX_QDEC_CONFIG_IRQ_PRIORITY  - Interrupt priority
1303 // <e> NRFX_QDEC_CONFIG_LOG_ENABLED - Enables logging in the module.
1308 // <o> NRFX_QDEC_CONFIG_LOG_LEVEL  - Default Severity level
1320 // <o> NRFX_QDEC_CONFIG_INFO_COLOR  - ANSI escape code prefix.
1336 // <o> NRFX_QDEC_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
1356 // <e> NRFX_RNG_ENABLED - nrfx_rng - RNG peripheral driver
1361 // <q> NRFX_RNG_CONFIG_ERROR_CORRECTION  - Error correction
1368 // <o> NRFX_RNG_CONFIG_IRQ_PRIORITY  - Interrupt priority
1383 // <e> NRFX_RNG_CONFIG_LOG_ENABLED - Enables logging in the module.
1388 // <o> NRFX_RNG_CONFIG_LOG_LEVEL  - Default Severity level
1400 // <o> NRFX_RNG_CONFIG_INFO_COLOR  - ANSI escape code prefix.
1416 // <o> NRFX_RNG_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
1436 // <e> NRFX_RTC_ENABLED - nrfx_rtc - RTC peripheral driver
1441 // <q> NRFX_RTC0_ENABLED  - Enable RTC0 instance
1448 // <q> NRFX_RTC1_ENABLED  - Enable RTC1 instance
1455 // <q> NRFX_RTC2_ENABLED  - Enable RTC2 instance
1462 // <o> NRFX_RTC_MAXIMUM_LATENCY_US - Maximum possible time[us] in highest priority interrupt
1467 // <o> NRFX_RTC_DEFAULT_CONFIG_FREQUENCY - Frequency  <16-32768>
1474 // <q> NRFX_RTC_DEFAULT_CONFIG_RELIABLE  - Ensures safe compare event triggering
1481 // <o> NRFX_RTC_DEFAULT_CONFIG_IRQ_PRIORITY  - Interrupt priority
1496 // <e> NRFX_RTC_CONFIG_LOG_ENABLED - Enables logging in the module.
1501 // <o> NRFX_RTC_CONFIG_LOG_LEVEL  - Default Severity level
1513 // <o> NRFX_RTC_CONFIG_INFO_COLOR  - ANSI escape code prefix.
1529 // <o> NRFX_RTC_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
1549 // <e> NRFX_SAADC_ENABLED - nrfx_saadc - SAADC peripheral driver
1554 // <o> NRFX_SAADC_CONFIG_RESOLUTION  - Resolution
1565 // <o> NRFX_SAADC_CONFIG_OVERSAMPLE  - Sample period
1581 // <q> NRFX_SAADC_CONFIG_LP_MODE  - Enabling low power mode
1588 // <o> NRFX_SAADC_CONFIG_IRQ_PRIORITY  - Interrupt priority
1603 // <e> NRFX_SAADC_CONFIG_LOG_ENABLED - Enables logging in the module.
1608 // <o> NRFX_SAADC_CONFIG_LOG_LEVEL  - Default Severity level
1620 // <o> NRFX_SAADC_CONFIG_INFO_COLOR  - ANSI escape code prefix.
1636 // <o> NRFX_SAADC_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
1656 // <e> NRFX_SPIM_ENABLED - nrfx_spim - SPIM peripheral driver
1661 // <q> NRFX_SPIM0_ENABLED  - Enable SPIM0 instance
1668 // <q> NRFX_SPIM1_ENABLED  - Enable SPIM1 instance
1675 // <q> NRFX_SPIM2_ENABLED  - Enable SPIM2 instance
1682 // <o> NRFX_SPIM_MISO_PULL_CFG  - MISO pin pull configuration.
1692 // <o> NRFX_SPIM_DEFAULT_CONFIG_IRQ_PRIORITY  - Interrupt priority
1707 // <e> NRFX_SPIM_CONFIG_LOG_ENABLED - Enables logging in the module.
1712 // <o> NRFX_SPIM_CONFIG_LOG_LEVEL  - Default Severity level
1724 // <o> NRFX_SPIM_CONFIG_INFO_COLOR  - ANSI escape code prefix.
1740 // <o> NRFX_SPIM_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
1758 // <q> NRFX_SPIM_NRF52_ANOMALY_109_WORKAROUND_ENABLED  - Enables nRF52 anomaly 109 workaround for S…
1762 // <i> a start event of zero-length transmission to start the clock. This
1774 // <e> NRFX_SPIS_ENABLED - nrfx_spis - SPIS peripheral driver
1779 // <q> NRFX_SPIS0_ENABLED  - Enable SPIS0 instance
1786 // <q> NRFX_SPIS1_ENABLED  - Enable SPIS1 instance
1793 // <q> NRFX_SPIS2_ENABLED  - Enable SPIS2 instance
1800 // <o> NRFX_SPIS_DEFAULT_CONFIG_IRQ_PRIORITY  - Interrupt priority
1815 // <o> NRFX_SPIS_DEFAULT_DEF - SPIS default DEF character  <0-255>
1822 // <o> NRFX_SPIS_DEFAULT_ORC - SPIS default ORC character  <0-255>
1829 // <e> NRFX_SPIS_CONFIG_LOG_ENABLED - Enables logging in the module.
1834 // <o> NRFX_SPIS_CONFIG_LOG_LEVEL  - Default Severity level
1846 // <o> NRFX_SPIS_CONFIG_INFO_COLOR  - ANSI escape code prefix.
1862 // <o> NRFX_SPIS_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
1880 // <q> NRFX_SPIS_NRF52_ANOMALY_109_WORKAROUND_ENABLED  - Enables nRF52 Anomaly 109 workaround for S…
1896 // <e> NRFX_SPI_ENABLED - nrfx_spi - SPI peripheral driver
1901 // <q> NRFX_SPI0_ENABLED  - Enable SPI0 instance
1908 // <q> NRFX_SPI1_ENABLED  - Enable SPI1 instance
1915 // <q> NRFX_SPI2_ENABLED  - Enable SPI2 instance
1922 // <o> NRFX_SPI_MISO_PULL_CFG  - MISO pin pull configuration.
1932 // <o> NRFX_SPI_DEFAULT_CONFIG_IRQ_PRIORITY  - Interrupt priority
1947 // <e> NRFX_SPI_CONFIG_LOG_ENABLED - Enables logging in the module.
1952 // <o> NRFX_SPI_CONFIG_LOG_LEVEL  - Default Severity level
1964 // <o> NRFX_SPI_CONFIG_INFO_COLOR  - ANSI escape code prefix.
1980 // <o> NRFX_SPI_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
2000 // <e> NRFX_SWI_ENABLED - nrfx_swi - SWI/EGU peripheral allocator
2005 // <q> NRFX_EGU_ENABLED  - Enable EGU support
2012 // <q> NRFX_SWI0_DISABLED  - Exclude SWI0 from being utilized by the driver
2019 // <q> NRFX_SWI1_DISABLED  - Exclude SWI1 from being utilized by the driver
2026 // <q> NRFX_SWI2_DISABLED  - Exclude SWI2 from being utilized by the driver
2033 // <q> NRFX_SWI3_DISABLED  - Exclude SWI3 from being utilized by the driver
2040 // <q> NRFX_SWI4_DISABLED  - Exclude SWI4 from being utilized by the driver
2047 // <q> NRFX_SWI5_DISABLED  - Exclude SWI5 from being utilized by the driver
2054 // <e> NRFX_SWI_CONFIG_LOG_ENABLED - Enables logging in the module.
2059 // <o> NRFX_SWI_CONFIG_LOG_LEVEL  - Default Severity level
2071 // <o> NRFX_SWI_CONFIG_INFO_COLOR  - ANSI escape code prefix.
2087 // <o> NRFX_SWI_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
2107 // <q> NRFX_SYSTICK_ENABLED  - nrfx_systick - ARM(R) SysTick driver
2114 // <e> NRFX_TIMER_ENABLED - nrfx_timer - TIMER periperal driver
2119 // <q> NRFX_TIMER0_ENABLED  - Enable TIMER0 instance
2126 // <q> NRFX_TIMER1_ENABLED  - Enable TIMER1 instance
2133 // <q> NRFX_TIMER2_ENABLED  - Enable TIMER2 instance
2140 // <q> NRFX_TIMER3_ENABLED  - Enable TIMER3 instance
2147 // <q> NRFX_TIMER4_ENABLED  - Enable TIMER4 instance
2154 // <o> NRFX_TIMER_DEFAULT_CONFIG_FREQUENCY  - Timer frequency if in Timer mode
2171 // <o> NRFX_TIMER_DEFAULT_CONFIG_MODE  - Timer mode or operation
2180 // <o> NRFX_TIMER_DEFAULT_CONFIG_BIT_WIDTH  - Timer counter bit width
2191 // <o> NRFX_TIMER_DEFAULT_CONFIG_IRQ_PRIORITY  - Interrupt priority
2206 // <e> NRFX_TIMER_CONFIG_LOG_ENABLED - Enables logging in the module.
2211 // <o> NRFX_TIMER_CONFIG_LOG_LEVEL  - Default Severity level
2223 // <o> NRFX_TIMER_CONFIG_INFO_COLOR  - ANSI escape code prefix.
2239 // <o> NRFX_TIMER_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
2259 // <e> NRFX_TWIM_ENABLED - nrfx_twim - TWIM peripheral driver
2264 // <q> NRFX_TWIM0_ENABLED  - Enable TWIM0 instance
2271 // <q> NRFX_TWIM1_ENABLED  - Enable TWIM1 instance
2278 // <o> NRFX_TWIM_DEFAULT_CONFIG_FREQUENCY  - Frequency
2288 // <q> NRFX_TWIM_DEFAULT_CONFIG_HOLD_BUS_UNINIT  - Enables bus holding after uninit
2295 // <o> NRFX_TWIM_DEFAULT_CONFIG_IRQ_PRIORITY  - Interrupt priority
2310 // <e> NRFX_TWIM_CONFIG_LOG_ENABLED - Enables logging in the module.
2315 // <o> NRFX_TWIM_CONFIG_LOG_LEVEL  - Default Severity level
2327 // <o> NRFX_TWIM_CONFIG_INFO_COLOR  - ANSI escape code prefix.
2343 // <o> NRFX_TWIM_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
2361 // <q> NRFX_TWIM_NRF52_ANOMALY_109_WORKAROUND_ENABLED  - Enables nRF52 anomaly 109 workaround for T…
2365 // <i> the start event of zero-frequency transmission, clear the
2366 // <i> peripheral, set desired frequency, start the peripheral, and
2376 // <e> NRFX_TWIS_ENABLED - nrfx_twis - TWIS peripheral driver
2381 // <q> NRFX_TWIS0_ENABLED  - Enable TWIS0 instance
2388 // <q> NRFX_TWIS1_ENABLED  - Enable TWIS1 instance
2395 // <q> NRFX_TWIS_ASSUME_INIT_AFTER_RESET_ONLY  - Assume that any instance would be initialized only…
2398 …ould be called. If you activate TWIS only once and do never uninitialize it - set this flag to 1 w…
2404 // <q> NRFX_TWIS_NO_SYNC_MODE  - Remove support for synchronous mode
2413 // <o> NRFX_TWIS_DEFAULT_CONFIG_ADDR0 - Address0
2418 // <o> NRFX_TWIS_DEFAULT_CONFIG_ADDR1 - Address1
2423 // <o> NRFX_TWIS_DEFAULT_CONFIG_SCL_PULL  - SCL pin pull configuration
2433 // <o> NRFX_TWIS_DEFAULT_CONFIG_SDA_PULL  - SDA pin pull configuration
2443 // <o> NRFX_TWIS_DEFAULT_CONFIG_IRQ_PRIORITY  - Interrupt priority
2458 // <e> NRFX_TWIS_CONFIG_LOG_ENABLED - Enables logging in the module.
2463 // <o> NRFX_TWIS_CONFIG_LOG_LEVEL  - Default Severity level
2475 // <o> NRFX_TWIS_CONFIG_INFO_COLOR  - ANSI escape code prefix.
2491 // <o> NRFX_TWIS_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
2511 // <e> NRFX_TWI_ENABLED - nrfx_twi - TWI peripheral driver
2516 // <q> NRFX_TWI0_ENABLED  - Enable TWI0 instance
2523 // <q> NRFX_TWI1_ENABLED  - Enable TWI1 instance
2530 // <o> NRFX_TWI_DEFAULT_CONFIG_FREQUENCY  - Frequency
2540 // <q> NRFX_TWI_DEFAULT_CONFIG_HOLD_BUS_UNINIT  - Enables bus holding after uninit
2547 // <o> NRFX_TWI_DEFAULT_CONFIG_IRQ_PRIORITY  - Interrupt priority
2562 // <e> NRFX_TWI_CONFIG_LOG_ENABLED - Enables logging in the module.
2567 // <o> NRFX_TWI_CONFIG_LOG_LEVEL  - Default Severity level
2579 // <o> NRFX_TWI_CONFIG_INFO_COLOR  - ANSI escape code prefix.
2595 // <o> NRFX_TWI_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
2615 // <e> NRFX_UARTE_ENABLED - nrfx_uarte - UARTE peripheral driver
2620 // <o> NRFX_UARTE0_ENABLED - Enable UARTE0 instance
2625 // <o> NRFX_UARTE_DEFAULT_CONFIG_HWFC  - Hardware Flow Control
2634 // <o> NRFX_UARTE_DEFAULT_CONFIG_PARITY  - Parity
2643 // <o> NRFX_UARTE_DEFAULT_CONFIG_BAUDRATE  - Default Baudrate
2668 // <o> NRFX_UARTE_DEFAULT_CONFIG_IRQ_PRIORITY  - Interrupt priority
2683 // <e> NRFX_UARTE_CONFIG_LOG_ENABLED - Enables logging in the module.
2688 // <o> NRFX_UARTE_CONFIG_LOG_LEVEL  - Default Severity level
2700 // <o> NRFX_UARTE_CONFIG_INFO_COLOR  - ANSI escape code prefix.
2716 // <o> NRFX_UARTE_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
2736 // <e> NRFX_UART_ENABLED - nrfx_uart - UART peripheral driver
2741 // <o> NRFX_UART0_ENABLED - Enable UART0 instance
2746 // <o> NRFX_UART_DEFAULT_CONFIG_HWFC  - Hardware Flow Control
2755 // <o> NRFX_UART_DEFAULT_CONFIG_PARITY  - Parity
2764 // <o> NRFX_UART_DEFAULT_CONFIG_BAUDRATE  - Default Baudrate
2789 // <o> NRFX_UART_DEFAULT_CONFIG_IRQ_PRIORITY  - Interrupt priority
2804 // <e> NRFX_UART_CONFIG_LOG_ENABLED - Enables logging in the module.
2809 // <o> NRFX_UART_CONFIG_LOG_LEVEL  - Default Severity level
2821 // <o> NRFX_UART_CONFIG_INFO_COLOR  - ANSI escape code prefix.
2837 // <o> NRFX_UART_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.
2857 // <e> NRFX_WDT_ENABLED - nrfx_wdt - WDT peripheral driver
2862 // <o> NRFX_WDT_CONFIG_BEHAVIOUR  - WDT behavior in CPU SLEEP or HALT mode
2873 // <o> NRFX_WDT_CONFIG_RELOAD_VALUE - Reload value  <15-4294967295>
2880 // <o> NRFX_WDT_CONFIG_NO_IRQ  - Remove WDT IRQ handling from WDT driver
2889 // <o> NRFX_WDT_CONFIG_IRQ_PRIORITY  - Interrupt priority
2904 // <e> NRFX_WDT_CONFIG_LOG_ENABLED - Enables logging in the module.
2909 // <o> NRFX_WDT_CONFIG_LOG_LEVEL  - Default Severity level
2921 // <o> NRFX_WDT_CONFIG_INFO_COLOR  - ANSI escape code prefix.
2937 // <o> NRFX_WDT_CONFIG_DEBUG_COLOR  - ANSI escape code prefix.