Lines Matching +full:7 +full:b
24 * <15> :: VDM type ( 1b == structured, 0b == unstructured )
27 * <10:8> :: object position (1-7 valid ... used for enter/exit mode only)
28 * <7:6> :: command type (SVDM only?)
70 #define VDO_CMD_FLASH_WRITE VDO_CMD_VENDOR(7)
116 * <26> :: modal operation supported (1b == yes)
184 * <23:22> :: Connector type (10b == receptacle, 11b == captive plug)
187 * <7> :: Vconn required (AMA only, 0b == no, 1b == yes)
188 * <6> :: Vbus required (AMA only, 0b == yes, 1b == no)
238 | ((vcpwr) & 0x7) << 8 | (vcr) << 7 | (vbr) << 6 | ((alt) & 0x7) << 3 \
247 * <23:22> :: Connector type (10b == receptacle, 11b == captive plug)
270 * <19:18> :: type-C to Type-A/B/C/Captive (00b == A, 01 == B, 10 == C, 11 == Captive)
273 * <12:11> :: cable termination type (11b == both ends active VCONN req)
274 * <10> :: SSTX1 Directionality support (0b == fixed, 1b == cfgable)
277 * <7> :: SSRX2 Directionality support
278 * <6:5> :: Vbus current handling capability (01b == 3A, 10b == 5A)
279 * <4> :: Vbus through cable (0b == no, 1b == yes)
280 * <3> :: SOP" controller present? (0b == no, 1b == yes)
289 * <19:18> :: Type-C to Type-C/Captive (10b == C, 11b == Captive)
292 * <12:11> :: cable termination type (10b == Vconn not req, 01b == Vconn req)
293 * <10:9> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V)
294 * <8:7> :: Reserved, Shall be set to zero
295 * <6:5> :: Vbus current handling capability (01b == 3A, 10b == 5A)
305 * <19:18> :: Connector type (10b == C, 11b == Captive)
308 * <12:11> :: cable termination type (10b == one end active, 11b == both ends active VCONN req)
309 * <10:9> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V)
310 * <8> :: SBU supported (0b == supported, 1b == not supported)
311 * <7> :: SBU type (0b == passive, 1b == active)
312 * <6:5> :: Vbus current handling capability (01b == 3A, 10b == 5A)
313 * <4> :: Vbus through cable (0b == no, 1b == yes)
314 * <3> :: SOP" controller present? (0b == no, 1b == yes)
334 #define CABLE_LATENCY_7M 7
374 | (tx2d) << 9 | (rx1d) << 8 | (rx2d) << 7 | ((cur) & 0x3) << 5 \
383 | ((vbm) & 0x3) << 9 | (sbu) << 8 | (sbut) << 7 | ((cur) & 0x3) << 5 \
396 * <11> :: U3 to U0 transition mode (0b == direct, 1b == through U3S)
397 * <10> :: Physical connection (0b == copper, 1b == optical)
398 * <9> :: Active element (0b == redriver, 1b == retimer)
399 * <8> :: USB4 supported (0b == yes, 1b == no)
400 * <7:6> :: USB2 hub hops consumed
401 * <5> :: USB2 supported (0b == yes, 1b == no)
402 * <4> :: USB3.2 supported (0b == yes, 1b == no)
403 * <3> :: USB lanes supported (0b == one lane, 1b == two lanes)
404 * <2> :: Optically isolated active cable (0b == no, 1b == yes)
406 * <0> :: USB gen (0b == gen1, 1b == gen2+)
449 * <11> :: SSTX1 Directionality support (0b == fixed, 1b == cfgable)
453 * <7:5> :: Vconn power
479 * <16:15> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V)
480 * <14> :: Charge through current support (0b == 3A, 1b == 5A)
482 * <12:7> :: Vbus impedance
484 * <0> :: Charge through support (0b == no, 1b == yes)
498 | ((vbm) & 0x3) << 15 | (curr) << 14 | ((vbi) & 0x3f) << 7 \