5   Linux Driver for BusLogic MultiMaster and FlashPoint SCSI Host Adapters
91   all BusLogic Host Adapters.
99   all BusLogic Host Adapters.
115   to be checked for potential BusLogic Host Adapters.  It is initialized by
242   multiple host adapters share the same IRQ Channel.
518 		   Some early BusLogic Host Adapters may not recover  in blogic_cmd()
604   SCSI Host Adapters by interrogating the PCI Configuration Space on PCI
606   I/O Addresses.  It returns the number of PCI MultiMaster Host Adapters found.
623 	   Iterate over the MultiMaster PCI Host Adapters.  For each  in blogic_init_mm_probeinfo()
629 	   the Primary I/O Address, then any other PCI host adapters,  in blogic_init_mm_probeinfo()
630 	   and finally any host adapters located at the remaining  in blogic_init_mm_probeinfo()
696 		   ISA Compatible I/O Port. On PCI Host Adapters, the  in blogic_init_mm_probeinfo()
763 			blogic_warn("BusLogic: Too many Host Adapters detected\n", NULL);  in blogic_init_mm_probeinfo()
769 	   MultiMaster BIOS will recognize MultiMaster Host Adapters in  in blogic_init_mm_probeinfo()
773 	   MultiMaster Host Adapters in the order they are enumerated by  in blogic_init_mm_probeinfo()
780 	   Iterate over the older non-compliant MultiMaster PCI Host Adapters,  in blogic_init_mm_probeinfo()
827   Host Adapters by interrogating the PCI Configuration Space.  It returns the
828   number of FlashPoint Host Adapters found.
836 	   Interrogate PCI Configuration Space for any FlashPoint Host Adapters.  in blogic_init_fp_probeinfo()
893 			blogic_warn("BusLogic: Too many Host Adapters detected\n", NULL);  in blogic_init_fp_probeinfo()
901 	   The FlashPoint BIOS will scan for FlashPoint Host Adapters in the order of  in blogic_init_fp_probeinfo()
912   Probe Information to be checked for potential BusLogic SCSI Host Adapters by
915   FlashPoint and PCI MultiMaster Host Adapters are present, this driver will
916   probe for FlashPoint Host Adapters first unless the BIOS primary disk is
918   MultiMaster Host Adapters will be probed first.  The BusLogic Driver Options
927 	   FlashPoint Host Adapters; otherwise, default to the standard  in blogic_init_probeinfo_list()
964 				   Adapters are probed before FlashPoint Host  in blogic_init_probeinfo_list()
965 				   Adapters.  in blogic_init_probeinfo_list()
1018 	   FlashPoint Host Adapters are Probed by the FlashPoint SCCB Manager.  in blogic_probe()
1057 	   an I/O port that responded.  Adaptec Host Adapters do not  in blogic_probe()
1065 	   earlier BusLogic Host Adapters, including the undocumented  in blogic_probe()
1093 	   FlashPoint Host Adapters are Hard Reset by the FlashPoint  in blogic_hwreset()
1202 	   FlashPoint Host Adapters do not require this protection.  in blogic_checkadapter()
1208 	   BusLogic Host Adapters and true clones support this command.  in blogic_checkadapter()
1209 	   Adaptec 1542C series Host Adapters that respond to the Geometry  in blogic_checkadapter()
1250 	   Configuration Information for FlashPoint Host Adapters is  in blogic_rdconfig()
1358 	   BusLogic MultiMaster Host Adapters can be identified by their  in blogic_rdconfig()
1362 	   5.xx       BusLogic "W" Series Host Adapters:  in blogic_rdconfig()
1364 	   4.xx       BusLogic "C" Series Host Adapters:  in blogic_rdconfig()
1366 	   3.xx       BusLogic "S" Series Host Adapters:  in blogic_rdconfig()
1369 	   2.xx       BusLogic "A" Series Host Adapters:  in blogic_rdconfig()
1418 	   and save the DMA Channel for ISA Host Adapters.  in blogic_rdconfig()
1466 	   Termination Information from "W" series MultiMaster Host Adapters.  in blogic_rdconfig()
1486 	   AutoSCSI data from "W" and "C" series MultiMaster Host Adapters.  in blogic_rdconfig()
1525 	   series MultiMaster Host Adapters.  in blogic_rdconfig()
1543 	   supported by this driver for Wide and Narrow Host Adapters.  in blogic_rdconfig()
1557 	   cause a substantial performance penalty.  The host adapters  in blogic_rdconfig()
1590 	   all "W" series MultiMaster Host Adapters, on "C" series  in blogic_rdconfig()
1591 	   MultiMaster Host Adapters with firmware version 4.22 and above,  in blogic_rdconfig()
1592 	   and on "S" series MultiMaster Host Adapters with firmware version  in blogic_rdconfig()
1616 	   BusLogic BT-445S Host Adapters prior to board revision E have a  in blogic_rdconfig()
1619 	   incorrectly.  Only properly functioning BT-445S Host Adapters  in blogic_rdconfig()
1628 	   Host Adapters.  in blogic_rdconfig()
1931 	   FlashPoint Host Adapters do not use Outgoing and Incoming Mailboxes.  in blogic_initadapter()
1986 	   For Host Adapters that support Extended LUN Format CCBs, issue the  in blogic_initadapter()
2038 	   FlashPoint Host Adapters do not provide for Target Device Inquiry.  in blogic_inquiry()
2048 	   Issue the Inquire Target Devices command for host adapters with  in blogic_inquiry()
2050 	   ID 0 to 7 command for older host adapters.  This is necessary to  in blogic_inquiry()
2194   blogic_init probes for BusLogic Host Adapters at the standard
2197   returns the number of BusLogic Host Adapters successfully initialized and
2316 		   BusLogic Host Adapters.  in blogic_init()
2383 			   BusLogic Host Adapters, destroy the CCBs, Release  in blogic_init()
2414 	   FlashPoint Host Adapters must first be released by the FlashPoint  in blogic_deladapter()
2431 	   Host Adapters.  in blogic_deladapter()
2736   Adapters.
3232   may be enabled in AutoSCSI on FlashPoint Host Adapters and on "W" and "C"
3233   series MultiMaster Host Adapters, or by a dip switch setting on "S" and "A"
3234   series MultiMaster Host Adapters.  With Extended Translation enabled, drives
3507   for multiple host adapters may be specified either by separating the option
3511   adapters whereas the remaining options apply individually only to the