Lines Matching full:added
35 * 05-24-00 00.10.02 Added MPI_IOCSTATUS_SCSI_RESIDUAL_MISMATCH definition.
37 * 06-22-00 01.00.02 Added MPI_IOCSTATUS_LAN_ definitions.
39 * Added MPI_MSGFLAGS_CONTINUATION_REPLY definition.
40 * 06-30-00 01.00.03 Added MPI_CONTEXT_REPLY_TYPE_LAN definition.
41 * Added MPI_GET/SET_CONTEXT_REPLY_TYPE macros.
42 * 07-27-00 01.00.04 Added MPI_FAULT_ definitions.
44 * Added MPI_IOCSTATUS_INTERNAL_ERROR definition.
45 * Added MPI_IOCSTATUS_TARGET_XFER_COUNT_MISMATCH.
47 * 12-04-00 01.01.02 Added new function codes.
48 * 01-09-01 01.01.03 Added more definitions to the system interface section
49 * Added MPI_IOCSTATUS_TARGET_STS_DATA_NOT_SENT.
52 * Added defines for MPI_DIAG_PREVENT_IOC_BOOT and
56 * Added function codes for RAID.
57 * 04-09-01 01.01.07 Added alternate define for MPI_DOORBELL_ACTIVE,
61 * Added define MPI_FUNCTION_TOOLBOX.
64 * 03-14-02 01.02.04 Added MPI_HEADER_VERSION_ defines.
66 * 07-12-02 01.02.06 Added define for MPI_FUNCTION_MAILBOX.
68 * 11-15-02 01.02.08 Added define MPI_IOCSTATUS_TARGET_INVALID_IO_INDEX and
72 * 01-16-04 01.02.11 Added define for MPI_IOCLOGINFO_TYPE_SHIFT.
73 * 04-29-04 01.02.12 Added function codes for MPI_FUNCTION_DIAG_BUFFER_POST
75 * Added MPI_IOCSTATUS_DIAGNOSTIC_RELEASED define.
78 * Added codes for Inband.
79 * 08-19-04 01.05.01 Added defines for Host Buffer Access Control doorbell.
80 * Added define for offset of High Priority Request Queue.
81 * Added new function codes and new IOCStatus codes.
82 * Added a IOCLogInfo type of SAS.
91 * 06-24-05 01.05.08 Added function codes for SCSI IO 32 and
93 * Added EEDP IOCStatus codes.
95 * 08-30-05 01.05.10 Added 2 new IOCStatus codes for Target.
106 * 05-24-00 00.10.02 Added _MSG_IOC_INIT_REPLY structure.
107 * 06-06-00 01.00.01 Added CurReplyFrameSize field to _MSG_IOC_FACTS_REPLY.
108 * 06-12-00 01.00.02 Added _MSG_PORT_ENABLE_REPLY structure.
109 * Added _MSG_EVENT_ACK_REPLY structure.
110 * Added _MSG_FW_DOWNLOAD_REPLY structure.
111 * Added _MSG_TOOLBOX_REPLY structure.
112 * 06-30-00 01.00.03 Added MaxLanBuckets to _PORT_FACT_REPLY structure.
113 * 07-27-00 01.00.04 Added _EVENT_DATA structure definitions for _SCSI,
118 * Added a value for Manufacturer to WhoInit
119 * 12-04-00 01.01.02 Modified IOCFacts reply, added FWUpload messages, and
121 * 01-09-01 01.01.03 Added event enabled and disabled defines.
122 * Added structures for FwHeader and DataHeader.
123 * Added ImageType to FwUpload reply.
125 * 02-27-01 01.01.05 Added event for RAID status change and its event data.
126 * Added IocNumber field to MSG_IOC_FACTS_REPLY.
127 * 03-27-01 01.01.06 Added defines for ProductId field of MPI_FW_HEADER.
128 * Added structure offset comments.
129 * 04-09-01 01.01.07 Added structure EVENT_DATA_EVENT_CHANGE.
133 * 08-31-01 01.02.02 Added event MPI_EVENT_SCSI_DEVICE_STATUS_CHANGE and
135 * Added event MPI_EVENT_ON_BUS_TIMER_EXPIRED.
136 * Added MPI_IOCINIT_FLAGS_DISCARD_FW_IMAGE.
139 * Added MPI_FW_DOWNLOAD_ITYPE_NVSTORE_DATA and
142 * 11-01-01 01.02.04 Added defines for MPI_EXT_IMAGE_HEADER ImageType field.
143 * 03-14-02 01.02.05 Added HeaderVersion field to MSG_IOC_FACTS_REPLY.
144 * 05-31-02 01.02.06 Added define for
146 * Added AliasIndex to EVENT_DATA_LOGOUT structure.
147 * 04-01-03 01.02.07 Added defines for MPI_FW_HEADER_SIGNATURE_.
148 * 06-26-03 01.02.08 Added new values to the product family defines.
149 * 04-29-04 01.02.09 Added IOCCapabilities field to MSG_IOC_FACTS_REPLY and
150 * added related defines.
152 * 08-19-04 01.05.01 Added four new fields to MSG_IOC_INIT.
153 * Added three new fields to MSG_IOC_FACTS_REPLY.
156 * Added two new PortTypes for the PortFacts reply.
157 * Added six new events along with their EventData
159 * Added a new MsgFlag to the FwDownload request to
162 * Added FW family codes for SAS product families.
163 * 10-05-04 01.05.02 Added ReplyFifoHostSignalingAddr field to
165 * 12-07-04 01.05.03 Added more defines for SAS Discovery Error event.
166 * 12-09-04 01.05.04 Added Unsupported device to SAS Device event.
167 * 01-15-05 01.05.05 Added event data for SAS SES Event.
168 * 02-09-05 01.05.06 Added MPI_FW_UPLOAD_ITYPE_FW_BACKUP define.
169 * 02-22-05 01.05.07 Added Host Page Buffer Persistent flag to IOC Facts
171 * 03-11-05 01.05.08 Added family code for 1068E family.
173 * 06-24-05 01.05.09 Added 5 new IOCFacts Reply IOCCapabilities bits.
174 * Added Max SATA Targets to SAS Discovery Error event.
175 * 08-30-05 01.05.10 Added 4 new events and their event data structures.
176 * Added new ReasonCode value for SAS Device Status Change
178 * Added new family code for FC949E.
179 * 03-27-06 01.05.11 Added MPI_IOCFACTS_CAPABILITY_TLR.
180 * Added additional Reason Codes and more event data fields
182 * Added EVENT_DATA_SAS_BROADCAST_PRIMITIVE structure and
184 * Added MPI_EVENT_SAS_SMP_ERROR and event data structure.
185 * Added MPI_EVENT_SAS_INIT_DEVICE_STATUS_CHANGE and event
187 * Added MPI_EVENT_SAS_INIT_TABLE_OVERFLOW and event
189 * Added MPI_EXT_IMAGE_TYPE_INITIALIZATION.
190 * 10-11-06 01.05.12 Added MPI_IOCFACTS_EXCEPT_METADATA_UNSUPPORTED.
191 * Added MaxInitiators field to PortFacts reply.
192 * Added SAS Device Status Change ReasonCode for
194 * Added MPI_EVENT_SAS_EXPANDER_STATUS_CHANGE and event
196 * Added new ImageType values for FWDownload and FWUpload
198 * 02-28-07 01.05.13 Added MPI_EVENT_PRIMITIVE_ASYNCHRONOUS_EVENT for SAS
202 * added _MULTI_PORT_DOMAIN.
203 * 05-24-07 01.05.14 Added Common Boot Block type to FWDownload Request.
204 * Added Common Boot Block type to FWUpload Request.
205 * 08-07-07 01.05.15 Added MPI_EVENT_SAS_INIT_RC_REMOVED define.
206 * Added MPI_EVENT_IR2_RC_DUAL_PORT_ADDED and
208 * Added SASAddress field to SAS Initiator Device Table
210 * 03-28-08 01.05.16 Added two new ReasonCode values to SAS Device Status
213 * Added MPI_EVENT_DSCVRY_ERR_DS_SATA_INIT_FAILURE define.
214 * Added MPI_EVENT_SAS_INIT_RC_INACCESSIBLE define.
220 * 06-08-00 01.00.02 Added _PAGEVERSION definitions for all pages.
221 * Added FcPhLowestVersion, FcPhHighestVersion, Reserved2
226 * Added _RESPONSE_ID_MASK definition to SCSI_PORT_1
228 * Added Information field and _INFO_PARAMS_NEGOTIATED
232 * Added BucketsRemaining to LAN_1 page, redefined the
236 * 06-30-00 01.00.04 Added MaxReplySize to LAN_1 page and updated the page
242 * Added Manufacturing pages, IO Unit Page 2, SCSI SPI
246 * 01-09-01 01.01.05 Added defines for page address formats.
252 * New fields added to FC Port Page 0 and some flags
255 * Added FC Port pages 6 and 7.
256 * 01-25-01 01.01.06 Added MaxInitiators field to FcPortPage0.
258 * Added some LinkType defines for FcPortPage0.
262 * Added definitions and structures for IOC Page 2 and
264 * 03-27-01 01.01.10 Added CONFIG_PAGE_FC_PORT_8 and CONFIG_PAGE_FC_PORT_9.
266 * Added VendorId and ProductRevLevel fields to
270 * Added structure offset comments.
271 * 04-09-01 01.01.11 Added some new defines for the PageAddress field and
273 * Added IO Unit Page 3.
277 * Added SepID and SepBus to RVP2 IMPhysicalDisk struct.
278 * Added defines for the SEP bits in RVP2 VolumeSettings.
281 * Added defines for SES, SAF-TE, and cross channel for
286 * Added define for MPI_CONFIG_PAGEATTR_RO_PERSISTENT.
288 * Added defines for MPI_FCPORTPAGE1_FLAGS_HARD_ALPA_ONLY
294 * Added defines for MPI_SCSIDEVPAGE1_CONF_WDTR_DISALLOWED
296 * Added OnBusTimerValue to CONFIG_PAGE_SCSI_PORT_1.
297 * Added rejected bits to SCSI Device Page 0 Information.
302 * Added structures for Manufacturing Page 4, IO Unit
305 * 10-04-01 01.02.04 Added define for MPI_CONFIG_PAGETYPE_RAID_PHYSDISK.
309 * Added generic defines for hot spare pools and RAID
311 * 11-01-01 01.02.05 Added define for MPI_IOUNITPAGE1_DISABLE_IR.
312 * 03-14-02 01.02.06 Added PCISlotNum field to CONFIG_PAGE_IOC_1 along with
314 * 05-31-02 01.02.07 Added a Flags field to CONFIG_PAGE_IOC_2_RAID_VOL in a
315 * reserved byte and added a define.
316 * Added define for
318 * Added new config page: CONFIG_PAGE_IOC_5.
319 * Added MaxAliases, MaxHardAliases, and NumCurrentAliases
321 * Added AltConnector and NumRequestedAliases fields to
323 * Added new config page: CONFIG_PAGE_FC_PORT_10.
324 * 07-12-02 01.02.08 Added more MPI_MANUFACTPAGE_DEVID_ defines.
325 * Added additional MPI_SCSIDEVPAGE0_NP_ defines.
326 * Added more MPI_SCSIDEVPAGE1_RP_ defines.
327 * Added define for
329 * Added new config page: CONFIG_PAGE_SCSI_DEVICE_3.
331 * 09-16-02 01.02.09 Added MPI_SCSIDEVPAGE1_CONF_FORCE_PPR_MSG define.
332 * 11-15-02 01.02.10 Added ConnectedID defines for CONFIG_PAGE_SCSI_PORT_0.
333 * Added more Flags defines for CONFIG_PAGE_FC_PORT_1.
334 * Added more Flags defines for CONFIG_PAGE_FC_DEVICE_0.
335 * 04-01-03 01.02.11 Added RR_TOV field and additional Flags defines for
337 * Added define MPI_FCPORTPAGE5_FLAGS_DISABLE to disable
339 * Added more device id defines.
340 * 06-26-03 01.02.12 Added MPI_IOUNITPAGE1_IR_USE_STATIC_VOLUME_ID define.
341 * Added TargetConfig and IDConfig fields to
343 * Added more PortFlags defines for CONFIG_PAGE_SCSI_PORT_2
345 * Added more Flags defines for CONFIG_PAGE_FC_PORT_1.
348 * Added MPI_FC_DEVICE_PAGE0_PROT_FCP_RETRY define.
349 * 01-16-04 01.02.13 Added InitiatorDeviceTimeout and InitiatorIoPendTimeout
351 * Added define for
353 * Added new fields to the substructures of
355 * 04-29-04 01.02.14 Added define for IDP bit for CONFIG_PAGE_SCSI_PORT_0,
359 * 05-11-04 01.03.01 Added structure for CONFIG_PAGE_INBAND_0.
362 * Added a new structure for extended config page header.
363 * Added new extended config pages types and structures for
372 * Added IO Unit Page 4.
373 * Added EEDP Flags settings to IOC Page 1.
374 * Added new BIOS Page 1 config page.
375 * 10-05-04 01.05.02 Added define for
377 * Added new Flags field to CONFIG_PAGE_MANUFACTURING_5 and
379 * Added more defines for SAS IO Unit Page 0
381 * Added define for MPI_SAS_IOUNIT0_DS_SUBTRACTIVE_LINK
383 * Added defines for Physical Mapping Modes to SAS IO Unit
385 * Added define for
387 * 10-27-04 01.05.03 Added defines for new SAS PHY page addressing mode.
388 * Added defines for MaxTargetSpinUp to BIOS Page 1.
389 * Added 5 new ControlFlags defines for SAS IO Unit
391 * Added MaxNumPhysicalMappedIDs field to SAS IO Unit
393 * Added AccessStatus field to SAS Device Page 0 and added
395 * 12-07-04 01.05.04 Added config page structures for BIOS Page 2, RAID
399 * Added DataScrubRate and ResyncRate to RAID Volume
401 * Added MPI_SAS_IOUNIT2_FLAGS_RESERVE_ID_0_FOR_BOOT
403 * 12-09-04 01.05.05 Added Target Mode Large CDB Enable to FC Port Page 1
405 * Added Auto Port Config flag define for SAS IOUNIT
407 * Added Disabled bad Phy define to Expander Page 1
409 * Added SAS/SATA device support to SAS IOUnit Page 1
411 * Added Unsupported device to SAS Dev Page 0 Flags field
412 * Added disable use SATA Hash Address for SAS IOUNIT
414 * 01-15-05 01.05.06 Added defaults for data scrub rate and resync rate to
416 * Added new defines for BIOS Page 1 IOCSettings field.
417 * Added ExtDiskIdentifier field to RAID Physical Disk
419 * Added new defines for SAS IO Unit Page 1 ControlFlags
421 * Added defines and structures for the new Log Page 0, a
423 * 02-09-05 01.05.07 Added InactiveStatus field to RAID Volume Page 0.
424 * Added WWID field to RAID Volume Page 1.
425 * Added PhysicalPort field to SAS Expander pages 0 and 1.
427 * Added Enclosure/Slot boot device format to BIOS Page 2.
431 * Added Inactive Volume Member flag RAID Physical Disk
434 * Added CONFIG_PAGE_SAS_ENCLOSURE_0.
435 * Added Slot and Enclosure fields to SAS Device Page 0.
436 * 06-24-05 01.05.09 Added EEDP defines to IOC Page 1.
437 * Added more RAID type defines to IOC Page 2.
438 * Added Port Enable Delay settings to BIOS Page 1.
439 * Added Bad Block Table Full define to RAID Volume Page 0.
440 * Added Previous State defines to RAID Physical Disk
442 * Added Max Sata Targets define for DiscoveryStatus field
444 * Added Device Self Test to Control Flags of SAS IO Unit
446 * Added Direct Attach Starting Slot Number define for SAS
448 * Added new fields in SAS Device Page 2 for enclosure
450 * Added OwnerDevHandle and Flags field to SAS PHY Page 0.
451 * Added IOC GPIO Flags define to SAS Enclosure Page 0.
455 * Added MPI_IOUNITPAGE1_SATA_WRITE_CACHE_DISABLE bit.
456 * Added NumDevsPerEnclosure field to SAS IO Unit page 2.
457 * Added MPI_SAS_IOUNIT2_FLAGS_HOST_ASSIGNED_PHYS_MAP
459 * Added EnclosureHandle field to SAS Expander page 0.
462 * 08-30-05 01.05.11 Added DeviceID for FC949E and changed the DeviceID for
464 * Added more defines for Manufacturing Page 4 Flags field.
465 * Added more defines for IOCSettings and added
467 * Added postpone SATA Init bit to SAS IO Unit Page 1
470 * 03-27-06 01.05.12 Added two new Flags defines for Manufacturing Page 4.
471 * Added Manufacturing Page 7.
472 * Added MPI_IOCPAGE2_CAP_FLAGS_RAID_64_BIT_ADDRESSING.
473 * Added IOC Page 6.
474 * Added PrevBootDeviceForm field to CONFIG_PAGE_BIOS_2.
475 * Added MaxLBAHigh field to RAID Volume Page 0.
476 * Added Nvdata version fields to SAS IO Unit Page 0.
477 * Added AdditionalControlFlags, MaxTargetPortConnectTime,
480 * 10-11-06 01.05.13 Added NumForceWWID field and ForceWWID array to
482 * Added Manufacturing pages 8 through 10.
483 * Added defines for supported metadata size bits in
485 * Added defines for metadata size bits in VolumeSettings
487 * Added SATA Link Reset settings, Enable SATA Asynchronous
491 * Added defines for Enclosure Devices Unmapped and
494 * Added more AccessStatus values for SAS Device Page 0.
495 * Added bit for SATA Asynchronous Notification Support in
497 * 02-28-07 01.05.14 Added ExtFlags field to Manufacturing Page 4.
498 * Added Disable SMART Polling for CapabilitiesFlags of
500 * Added Disable SMART Polling to DeviceSettings of BIOS
502 * Added Multi-Port Domain bit for DiscoveryStatus field
504 * Added Multi-Port Domain Illegal flag for SAS IO Unit
506 * 05-24-07 01.05.15 Added Hide Physical Disks with Non-Integrated RAID
508 * Added Internal Connector to End Device Present bit to
512 * 08-07-07 01.05.16 Added MPI_IOCPAGE6_CAP_FLAGS_MULTIPORT_DRIVE_SUPPORT
514 * Added BIOS Page 4 structure.
515 * Added MPI_RAID_PHYS_DISK1_PATH_MAX define for RAID
517 * 01-15-07 01.05.17 Added additional bit defines for ExtFlags field of
519 * Added Solid State Drives Supported bit to IOC Page 6
521 * Added new value for AccessStatus field of SAS Device
530 * 05-24-00 00.10.02 Added SenseBufferLength to _MSG_SCSI_IO_REPLY.
532 * 06-08-00 01.00.02 Added MPI_SCSI_RSP_INFO_ definitions.
534 * 12-04-00 01.01.02 Added MPI_SCSIIO_CONTROL_NO_DISCONNECT.
536 * 03-27-01 01.01.04 Added structure offset comments.
537 * 04-10-01 01.01.05 Added new MsgFlag for MSG_SCSI_TASK_MGMT.
539 * 08-29-01 01.02.02 Added MPI_SCSITASKMGMT_TASKTYPE_LOGICAL_UNIT_RESET.
540 * Added MPI_SCSI_STATE_QUEUE_TAG_REJECTED for
542 * 09-28-01 01.02.03 Added structures and defines for SCSI Enclosure
544 * 10-04-01 01.02.04 Added defines for SEP request Action field.
545 * 05-31-02 01.02.05 Added MPI_SCSIIO_MSGFLGS_CMD_DETERMINES_DATA_DIR define
547 * 11-15-02 01.02.06 Added special extended SCSI Status defines for FCP.
548 * 06-26-03 01.02.07 Added MPI_SCSI_STATUS_FCPEXT_UNASSIGNED define.
550 * 08-19-04 01.05.01 Added MsgFlags defines for EEDP to SCSI IO request.
551 * Added new word to MSG_SCSI_IO_REPLY to add TaskTag field
553 * Added new MSG_SCSI_IO32_REQUEST structure.
554 * Added a TaskType of Clear Task Set to SCSI
556 * 12-07-04 01.05.02 Added support for Task Management Query Task.
564 * 06-24-05 01.05.05 Added SCSI IO 32 structures and defines.
565 * Added four new defines for SEP SlotStatus.
568 * 03-27-06 01.05.07 Added Task Management type of Clear ACA.
577 * 06-22-00 01.00.02 Added _MSG_TARGET_CMD_BUFFER_POST_REPLY structure.
581 * HostIndex and IocIndex. Added Alias.
582 * 01-09-01 01.01.02 Added defines for TARGET_ASSIST_FLAGS_REPOST_CMD_BUFFER
585 * Added structures for MPI_TARGET_SCSI_SPI_CMD_BUFFER and
587 * 03-27-01 01.01.04 Added structure offset comments.
589 * 09-28-01 01.02.02 Added structure for MPI_TARGET_SCSI_SPI_STATUS_IU.
590 * Added PriorityReason field to some replies and
592 * Added some defines for to support previous version
594 * 10-04-01 01.02.03 Added PriorityReason to MSG_TARGET_ERROR_REPLY.
595 * 11-01-01 01.02.04 Added define for TARGET_STATUS_SEND_FLAGS_HIGH_PRIORITY.
600 * Added AliasIndex field to MPI_TARGET_FCP_CMD_BUFFER.
601 * 09-16-02 01.02.07 Added flags for confirmed completion.
602 * Added PRIORITY_REASON_TARGET_BUSY.
603 * 11-15-02 01.02.08 Added AliasID field to MPI_TARGET_SCSI_SPI_CMD_BUFFER.
604 * 04-01-03 01.02.09 Added OptionalOxid field to MPI_TARGET_FCP_CMD_BUFFER.
606 * 08-19-04 01.05.01 Added new request message structures for
610 * Added new structures for SAS SSP Command buffer, SSP
612 * 10-05-04 01.05.02 MSG_TARGET_CMD_BUFFER_POST_BASE_LIST_REPLY added.
615 * 06-24-05 01.05.05 Added TargetAssistExtended structures and defines.
616 * 03-27-06 01.05.06 Added a comment.
622 * 06-12-00 01.00.02 Added _MSG_FC_ABORT_REPLY structure.
624 * 12-04-00 01.01.02 Added messages for Common Transport Send and
630 * Added FC_ABORT_TYPE_CT_SEND_REQUEST and
632 * Added MPI_FC_PRIM_SEND_FLAGS_STOP_SEND.
634 * 03-27-01 01.01.06 Added Flags field to MSG_LINK_SERVICE_BUFFER_POST_REPLY
636 * Added MPI_FC_PRIM_SEND_FLAGS_RESET_LINK define.
637 * Added structure offset comments.
638 * 04-09-01 01.01.07 Added RspLength field to MSG_LINK_SERVICE_RSP_REQUEST.
643 * 01-16-04 01.02.04 Added define for MPI_FC_PRIM_SEND_FLAGS_ML_RESET_LINK.
650 * 05-24-00 00.10.02 Added LANStatus field to _MSG_LAN_SEND_REPLY.
651 * Added LANStatus field to _MSG_LAN_RECEIVE_POST_REPLY.
654 * 06-12-00 01.00.02 Added MPI_ to BUCKETSTATUS_ definitions.
656 * 06-30-00 01.00.04 Added Context Reply definitions per revised proposal.
662 * 03-27-01 01.01.03 Added structure offset comments.
670 * 03-27-01 01.01.02 Added structure offset comments.
672 * 08-29-01 01.02.02 Added DIAG_DATA_UPLOAD_HEADER and related defines.
674 * 10-04-01 01.02.03 Added ActionData defines for
676 * 11-01-01 01.02.04 Added define for MPI_RAID_ACTION_ADATA_DO_NOT_SYNC.
677 * 03-14-02 01.02.05 Added define for MPI_RAID_ACTION_ADATA_LOW_LEVEL_INIT.
678 * 05-07-02 01.02.06 Added define for MPI_RAID_ACTION_ACTIVATE_VOLUME,
681 * 07-12-02 01.02.07 Added structures for Mailbox request and reply.
682 * 11-15-02 01.02.08 Added missing MsgContext field to MSG_MAILBOX_REQUEST.
687 * 01-15-05 01.05.02 Added defines for the two new RAID Actions for
689 * 02-28-07 01.05.03 Added new RAID Action, Device FW Update Mode, and
691 * 08-07-07 01.05.04 Added Disable Full Rebuild bit to the ActionDataWord
693 * 01-15-08 01.05.05 Added define for MPI_RAID_ACTION_SET_VOLUME_NAME.
698 * 08-29-01 01.02.02 Added DIAG_DATA_UPLOAD_HEADER and related defines.
699 * 01-16-04 01.02.03 Added defines and structures for new tools
702 * 04-29-04 01.02.04 Added message structures for Diagnostic Buffer Post and
706 * 10-06-04 01.05.02 Added define for MPI_DIAG_BUF_TYPE_COUNT.
707 * 02-09-05 01.05.03 Added frame size option to FC management tool.
708 * Added Beacon tool to the Toolbox.
718 * 08-30-05 01.05.02 Added DeviceInfo bit for SEP.
719 * Added PrimFlags and Primitive field to SAS IO Unit
720 * Control request, and added a new operation code.
721 * 03-27-06 01.05.03 Added Force Full Discovery, Transmit Port Select Signal,
723 * Added DevHandle field to SAS IO Unit Control request and
727 * 01-15-08 01.05.05 Added support for MPI_SAS_OP_SET_IOC_PARAMETER,
730 * Added MPI_SAS_DEVICE_INFO_PRODUCT_SPECIFIC define.
737 * 02-20-01 01.01.02 Added define and ifdef for MPI_POINTER.
741 * 08-30-05 01.05.02 Added PowerPC option to #ifdef's.