Lines Matching +full:leds +full:- +full:trigger +full:- +full:pattern
1 # SPDX-License-Identifier: GPL-2.0-only
19 LEDs from both userspace and optionally, by kernel events (triggers).
26 This option enables the LED sysfs class in /sys/class/leds. You'll
27 need this to do anything useful with LEDs. If unsure, say Y.
33 This option enables the flash LED sysfs class in /sys/class/leds.
34 It wraps LED Class and adds flash LEDs specific sysfs attributes
43 This option enables the multicolor LED sysfs class in /sys/class/leds.
46 for multicolor LEDs that are grouped together. This class is not
47 intended for single color LEDs. It can be built as a module.
54 for LED sysfs class devices under /sys/class/leds.
56 See Documentation/ABI/testing/sysfs-class-led for details.
65 This option enables support for on-chip LED drivers found on Marvell
72 This option enables support for the AN30259A 3-channel
76 will be called leds-an30259a.
83 This driver makes the PC Engines APU1 front panel LEDs
86 If you're looking for APU2/3, use the pcengines-apu2 driver.
90 module will be called leds-apu.
98 LEDs on Dell Wyse 3020 (Ariel) board via the KB3930 Embedded
110 a set of individually controlled LEDs and support 3 pattern controllers
112 - AW20036 (3x12) 36 LEDs
113 - AW20054 (6x9) 54 LEDs
114 - AW20072 (6x12) 72 LEDs
115 - AW20108 (9x12) 108 LEDs
118 will be called leds-aw200xx.
125 This option enables support for the AW2013 3-channel
129 will be called leds-aw2013.
137 This option enables support for LEDs connected to the BCM6328
146 This option enables support for LEDs connected to the BCM6358
154 This option enables support for charger and general purpose LEDs
158 will be called leds-cht-wcove.
166 This option enables support for LEDs offered by Motorola's
180 will be called leds-cr0014114.
189 This option enables support for LEDs managed by ChromeOS ECs.
190 All LEDs exposed by the EC are supported in multicolor mode.
191 A hardware trigger to switch back to the automatic behaviour is
195 will be called leds-cros_ec.
208 will be called leds-el15203000.
224 This option enables basic support for the LEDs found on the front
225 side of CZ.NIC's Turris Omnia router. There are 12 RGB LEDs on the
254 This option enables support for the LEDs on National Semiconductor /
257 The LEDs can be controlled directly, through PWM input, or by the
258 ambient-light-sensor interface. The chip supports
259 hardware-accelerated blinking with maximum on and off periods of 9.8
267 This option enables support for LEDs connected to LM3642.
268 The LM3642 is a 4MHz fixed-frequency synchronous boost
269 converter plus 1.5A constant current driver for a high-current
285 This option enables support for the LEDs on Sharp Locomo.
286 Zaurus models SL-5500 and SL-5600.
301 This option enables support for on-chip LED drivers found on
313 tristate "LED Support for the WRAP series LEDs"
317 This option enables support for the PCEngines WRAP programmable LEDs.
331 This option enables support for the Cobalt Raq series LEDs.
340 It uses a one-wire interface to control up to 1024 LEDs.
349 LEDs on the I/O and CPU boards of SunFire UltraSPARC servers.
387 tristate "LED Support for GPIO connected LEDs"
391 This option enables support for the LEDs connected to GPIO
392 outputs. To be useful the particular board must have LEDs
393 and they must be connected to the GPIO lines. The LEDs must be
402 This option enables support for LEDs connected to the National
407 module will be called leds-lp3944.
416 This option enables support for LEDs connected to the Texas
420 module will be called leds-lp3952.
431 module will be called leds-lp50xx.
503 This option enables support for the Keyboard LEDs on the LP8788 PMIC.
512 This option enables support for the display cluster LEDs
521 If you say yes here you get support for the TI LP8864-Q1,
522 LP8864S-Q1, LP8866-Q1, LP8866S-Q1 4/6 channel LED backlight
526 module will be called leds-lp8864.
534 programs through the LEDs subsystem. This LED has three
537 The driver supports two kinds of interface: using ledtrig-timer
538 or through /sys/class/leds/clevo::mail/brightness. As this LED
557 module will be called leds-clevo-mail.
564 This option enables support for LEDs connected to PCA955x
584 This option enables support for LEDs connected to the PCA963x
593 This option enables support for LEDs connected to PCA995x
602 This option enables support for LEDs available on embedded
606 will be called qnap-mcu-leds.
609 tristate "LED support for status LEDs on WM831x PMICs"
613 This option enables support for the status LEDs of the WM831x
621 This option enables support for LEDs driven by the Wolfson
629 This option enables support for on-chip LED drivers found
633 tristate "Dialog DA9052/DA9053 LEDS"
637 This option enables support for on-chip LED drivers found
638 on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs.
646 which can be used to control up to four LEDs.
653 This option enables support for pwm driven LEDs
660 This option enables support for regulator driven LEDs.
674 be called leds-bd2606mvv.
692 drive or power LEDs on the front panel. Using this driver
700 This option enables support for LEDs driven by a Linear Technology
701 LT3593 controller. This controller uses a special one-wire pulse
709 This option enables support for on-chip LED drivers found
713 be called leds-adp5520.
721 switch indication LEDs via the I2C bus.
724 be called leds-max5970.
731 This option enables support for on-chip LED drivers found
735 tristate "LED support for Network Space v2 GPIO LEDs"
740 This option enables support for the dual-GPIO LEDs found on the
746 n090401 (Seagate NAS 4-Bay)
749 tristate "LED support for Big Network series LEDs"
755 This option enables support for LEDs found on the LaCie 2Big
756 and 5Big Network v2 boards. The LEDs are wired to a CPLD and are
763 This option enables support for LEDs connected to TC6507
765 Driver support brightness control and hardware-assisted blinking.
779 LEDs driver for MAX77650 family of PMICs from Maxim Integrated.
785 This option enables support for on-chip LED drivers on
793 This option enables support for LEDs connected to LM3554
800 This option enables support for the LEDs on the Bachmann OT200.
801 Say Y to enable LEDs on the Bachmann OT200.
807 Say Y here to include support for the MEN 14F021P00 BMC LEDs.
810 will be called leds-menf21bmc.
817 This option enables support for LEDs connected to ISSI IS31FL319x
822 called leds-is31fl319x.
828 Say Y here to include support for ISSI IS31FL32XX and Si-En SN32xx
829 LED controllers. They are I2C devices with multiple constant-current
830 channels, each with independent 256-level PWM control.
838 LEDs.
841 called leds-sc27xx-bltc.
847 This option enables support for the UP board LEDs.
850 called leds-upboard.
876 This option enables support for the system LEDs present on
879 will be called leds-powernv.
882 bool "LED support for LEDs on system controllers"
887 This option enables support for the LEDs on syscon type
904 This option enables support for the LEDs on the Mellanox
911 This option enables support for the LEDs on the Mellanox Ethernet and
914 module, choose 'M' here: the module will be called leds-mlxreg.
920 This option enables support for userspace LEDs. Say 'y' to enable this
929 This option enables support for the User1 and User2 LEDs on NI
933 will be called leds-nic78bx.
975 Say Y to enable support for LEDs connected to LED1202
985 It is a single boost converter primarily for white LEDs and
993 This option enables support for the Red and White LEDs of
997 will be called leds-ip30.
1006 source "drivers/leds/blink/Kconfig"
1009 source "drivers/leds/flash/Kconfig"
1012 source "drivers/leds/rgb/Kconfig"
1015 source "drivers/leds/trigger/Kconfig"
1018 source "drivers/leds/simple/Kconfig"