Lines Matching +full:bcm6328 +full:- +full:gpio
1 # SPDX-License-Identifier: GPL-2.0-only
56 See Documentation/ABI/testing/sysfs-class-led for details.
65 This option enables support for on-chip LED drivers found on Marvell
72 This option enables support for the AN30259A 3-channel
76 will be called leds-an30259a.
86 If you're looking for APU2/3, use the pcengines-apu2 driver.
90 module will be called leds-apu.
112 - AW20036 (3x12) 36 LEDs
113 - AW20054 (6x9) 54 LEDs
114 - AW20072 (6x12) 72 LEDs
115 - AW20108 (9x12) 108 LEDs
118 will be called leds-aw200xx.
125 This option enables support for the AW2013 3-channel
129 will be called leds-aw2013.
132 tristate "LED Support for Broadcom BCM6328"
137 This option enables support for LEDs connected to the BCM6328
158 will be called leds-cht-wcove.
180 will be called leds-cr0014114.
195 will be called leds-cros_ec.
208 will be called leds-el15203000.
258 ambient-light-sensor interface. The chip supports
259 hardware-accelerated blinking with maximum on and off periods of 9.8
268 The LM3642 is a 4MHz fixed-frequency synchronous boost
269 converter plus 1.5A constant current driver for a high-current
286 Zaurus models SL-5500 and SL-5600.
301 This option enables support for on-chip LED drivers found on
340 It uses a one-wire interface to control up to 1024 LEDs.
377 bool "Enable GPIO support for PCA9532"
381 Allow unused pins on PCA9532 to be used as gpio.
383 To use a pin as gpio pca9532_type in pca9532_platform data needs to
387 tristate "LED Support for GPIO connected LEDs"
391 This option enables support for the LEDs connected to GPIO
393 and they must be connected to the GPIO lines. The LEDs must be
407 module will be called leds-lp3944.
420 module will be called leds-lp3952.
431 module will be called leds-lp50xx.
521 If you say yes here you get support for the TI LP8864-Q1,
522 LP8864S-Q1, LP8866-Q1, LP8866S-Q1 4/6 channel LED backlight
526 module will be called leds-lp8864.
537 The driver supports two kinds of interface: using ledtrig-timer
557 module will be called leds-clevo-mail.
569 bool "Enable GPIO support for PCA955X"
573 Allow unused pins on PCA955X to be used as gpio.
575 To use a pin as gpio the pin type should be set to
606 will be called qnap-mcu-leds.
629 This option enables support for on-chip LED drivers found
637 This option enables support for on-chip LED drivers found
638 on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs.
674 be called leds-bd2606mvv.
701 LT3593 controller. This controller uses a special one-wire pulse
709 This option enables support for on-chip LED drivers found
713 be called leds-adp5520.
724 be called leds-max5970.
731 This option enables support for on-chip LED drivers found
735 tristate "LED support for Network Space v2 GPIO LEDs"
740 This option enables support for the dual-GPIO LEDs found on the
746 n090401 (Seagate NAS 4-Bay)
757 controlled through a GPIO extension bus.
765 Driver support brightness control and hardware-assisted blinking.
785 This option enables support for on-chip LED drivers on
810 will be called leds-menf21bmc.
822 called leds-is31fl319x.
828 Say Y here to include support for ISSI IS31FL32XX and Si-En SN32xx
829 LED controllers. They are I2C devices with multiple constant-current
830 channels, each with independent 256-level PWM control.
841 called leds-sc27xx-bltc.
850 called leds-upboard.
879 will be called leds-powernv.
914 module, choose 'M' here: the module will be called leds-mlxreg.
933 will be called leds-nic78bx.
997 will be called leds-ip30.