Lines Matching +full:touch +full:- +full:key +full:- +full:connected
1 # SPDX-License-Identifier: GPL-2.0-only
44 tristate "AB8500 Pon (PowerOn) Key"
47 Say Y here to use the PowerOn Key for ST-Ericsson's AB8500
48 Mix-Sig PMIC.
51 will be called ab8500-ponkey.
54 tristate "Analog Devices AD714x Capacitance Touch Sensor"
56 Say Y here if you want to support an AD7142/3/7/8/7A touch sensor.
71 module will be called ad714x-i2c.
81 module will be called ad714x-spi.
92 will be called ariel-pwrbutton.
102 module will be called arizona-haptics.
113 module will be called atc260x-onkey.
116 tristate "Atmel Capacitive Touch Button Driver"
120 Say Y here if an Atmel Capacitive Touch Button device which
121 implements "captouch" protocol is connected to I2C bus. Typically
122 this device consists of Atmel Touch sensor controlled by AtMegaXX
130 tristate "NXP BBNSM Power Key Driver"
158 module will be called cs40l50-vibra.
183 tristate "Qualcomm PM8941 power key support"
186 Say Y here if you want support for the power key usually found
192 will be called pm8941-pwrkey.
200 on Qualcomm PM8xxx chip. This driver supports ff-memless interface
204 module will be called pm8xxx-vibrator.
207 tristate "PMIC8XXX power key support"
210 Say Y here if you want support for the PMIC8XXX power key.
215 module will be called pmic8xxx-pwrkey.
240 will be called max77650-onkey.
251 module will be called max77693-haptic.
269 on MAXIM MAX8997 chip. This driver supports ff-memless interface
273 module will be called max8997-haptic.
283 will be called mc13783-pwrbutton.
286 tristate "MMA8450 - Freescale's 3-Axis, 8/12-bit Digital Accelerometer"
312 Say Y here if you have a beeper connected to a GPIO pin.
315 module will be called gpio-beeper.
338 called gpio-vibra.
353 Say Y here if you want to enable power key reporting via the
357 be called cpcap-pwrbutton.
368 laptops of various brands, including Acer and Fujitsu-Siemens. If
391 ATI Remote Wonder II comes with some ATI's All-In-Wonder video cards
405 Currently only the UIA-11 type of receiver has been tested. The tag
407 will tell you what type of DMR you have. The UIA-10 type is not
415 tristate "Kionix KXTJ9 tri-axis digital accelerometer"
418 Say Y here to enable support for the Kionix KXTJ9 digital tri-axis
441 tristate "Yealink usb-p1k voip phone"
446 Yealink usb-p1k usb phones. The audio part is enabled by the generic
456 tristate "C-Media CM109 USB I/O Controller"
461 C-Media CM109 usb phones. The audio part is enabled by the generic
473 by a regulator. This driver supports ff-memless interface
477 module will be called regulator-haptic.
483 Say Y here if you want to enable power key reporting via the
487 be called retu-pwrbutton.
497 be called tps65218-pwrbutton.
507 be called tps65219-pwrbutton.
510 tristate "X-Powers AXP20X power button driver"
513 Say Y here if you want to enable power key reporting via the
517 be called axp20x-pek.
524 Say Y here if you want to enable power key reporting via the
555 subsystem accessible under char device 10:223 - /dev/input/uinput.
574 Say Y here if you want to support the built-in real time clock
581 Say Y here if you want to enable power key reporting via the
598 Say Y here if you want to support a keypad connected via I2C
613 called pwm-beeper.
625 called pwm-vibra.
628 tristate "Rockchip RK805 PMIC power key support"
631 Select this option to enable power key driver for RK805.
639 tristate "Rotary encoders connected to GPIO pins"
642 Say Y here to add support for rotary encoders connected to GPIO lines.
643 Check file:Documentation/input/devices/rotary-encoder.rst for more
717 Say Y here if you want to use Power key and Headphone button
724 tristate "Analog Devices ADXL34x Three-Axis Digital Accelerometer"
728 ADXL345/6 controller, and your board-specific initialization
748 module will be called adxl34x-i2c.
758 module will be called adxl34x-spi.
764 Say Y here if you have an IBM Operation Panel connected to your system
765 over I2C. The panel is typically connected only to a system's service
776 called ibm-panel.
789 tristate "Azoteq IQS269A capacitive touch controller"
794 touch controller.
800 tristate "Azoteq IQS626A capacitive touch controller"
805 touch controller.
811 tristate "Azoteq IQS7222A/B/C/D capacitive touch controller"
815 of capacitive touch controllers.
821 tristate "VTI CMA3000 Tri-axis accelerometer"
850 This driver implements the front-end of the Xen virtual
851 keyboard and mouse device driver. It communicates with a back-end
855 module will be called xen-kbdfront.
868 tristate "Windows-compatible SoC Button Array"
871 Say Y here if you have a SoC-based tablet that originally runs
887 module will be called drv260x-haptics.
898 module will be called drv2665-haptics.
909 module will be called drv2667-haptics.
927 This includes a polled power-button as well as a beeper.
930 module will be called qnap-mcu-input.
936 Say Y here if you want to enable power key reporting from RAVE SP
939 module will be called rave-sp-pwrbutton.
952 tristate "RT5120 PMIC power key support"
955 This enables support for RT5120 PMIC power key driver.
958 be called rt5120-pwrkey.
965 can be used to wakeup from low power modes and force a shut-down on