Lines Matching +full:board +full:- +full:delay +full:- +full:ps
1 // SPDX-License-Identifier: GPL-2.0
3 * Device Tree Source for the Eagle board with R-Car V3M
5 * Copyright (C) 2016-2017 Renesas Electronics Corp.
9 /dts-v1/;
11 #include <dt-bindings/gpio/gpio.h>
14 model = "Renesas Eagle board based on r8a77970";
29 stdout-path = "serial0:115200n8";
32 d1p8: regulator-fixed {
33 compatible = "regulator-fixed";
34 regulator-name = "fixed-1.8V";
35 regulator-min-microvolt = <1800000>;
36 regulator-max-microvolt = <1800000>;
37 regulator-boot-on;
38 regulator-always-on;
41 d3p3: regulator-fixed {
42 compatible = "regulator-fixed";
43 regulator-name = "fixed-3.3V";
44 regulator-min-microvolt = <3300000>;
45 regulator-max-microvolt = <3300000>;
46 regulator-boot-on;
47 regulator-always-on;
50 hdmi-out {
51 compatible = "hdmi-connector";
56 remote-endpoint = <&adv7511_out>;
61 lvds-decoder {
64 vcc-supply = <&d3p3>;
67 #address-cells = <1>;
68 #size-cells = <0>;
73 remote-endpoint = <&lvds0_out>;
80 remote-endpoint = <&adv7511_in>;
92 x1_clk: x1-clock {
93 compatible = "fixed-clock";
94 #clock-cells = <0>;
95 clock-frequency = <148500000>;
100 pinctrl-0 = <&avb_pins>;
101 pinctrl-names = "default";
103 renesas,no-ether-link;
104 phy-handle = <&phy0>;
105 rx-internal-delay-ps = <1800>;
106 tx-internal-delay-ps = <2000>;
109 phy0: ethernet-phy@0 {
110 compatible = "ethernet-phy-id0022.1622",
111 "ethernet-phy-ieee802.3-c22";
112 rxc-skew-ps = <1500>;
114 interrupts-extended = <&gpio1 17 IRQ_TYPE_LEVEL_LOW>;
115 reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
120 pinctrl-0 = <&canfd0_pins>;
121 pinctrl-names = "default";
135 clock-lanes = <0>;
136 data-lanes = <1 2 3 4>;
137 remote-endpoint = <&max9286_out0>;
145 clock-names = "du.0", "dclkin.0";
150 clock-frequency = <16666666>;
154 clock-frequency = <32768>;
158 pinctrl-0 = <&i2c0_pins>;
159 pinctrl-names = "default";
162 clock-frequency = <400000>;
167 gpio-controller;
168 #gpio-cells = <2>;
174 interrupts-extended = <&gpio1 20 IRQ_TYPE_LEVEL_LOW>;
176 avdd-supply = <&d1p8>;
177 dvdd-supply = <&d1p8>;
178 pvdd-supply = <&d1p8>;
179 dvdd-3v-supply = <&d3p3>;
180 bgvdd-supply = <&d1p8>;
182 adi,input-depth = <8>;
183 adi,input-colorspace = "rgb";
184 adi,input-clock = "1x";
187 #address-cells = <1>;
188 #size-cells = <0>;
193 remote-endpoint = <&thc63lvd1024_out>;
200 remote-endpoint = <&hdmi_con_out>;
208 pinctrl-0 = <&i2c3_pins>;
209 pinctrl-names = "default";
212 clock-frequency = <400000>;
214 gmsl0: gmsl-deserializer@48 {
218 maxim,gpio-poc = <0 GPIO_ACTIVE_LOW>;
219 enable-gpios = <&io_expander 0 GPIO_ACTIVE_HIGH>;
222 #address-cells = <1>;
223 #size-cells = <0>;
244 clock-lanes = <0>;
245 data-lanes = <1 2 3 4>;
246 remote-endpoint = <&csi40_in>;
251 i2c-mux {
252 #address-cells = <1>;
253 #size-cells = <0>;
256 #address-cells = <1>;
257 #size-cells = <0>;
264 #address-cells = <1>;
265 #size-cells = <0>;
272 #address-cells = <1>;
273 #size-cells = <0>;
280 #address-cells = <1>;
281 #size-cells = <0>;
296 remote-endpoint = <&thc63lvd1024_in>;
303 pinctrl-0 = <&scif_clk_pins>;
304 pinctrl-names = "default";
343 pinctrl-0 = <&qspi0_pins>;
344 pinctrl-names = "default";
349 compatible = "spansion,s25fs512s", "jedec,spi-nor";
351 spi-max-frequency = <50000000>;
352 spi-rx-bus-width = <4>;
355 compatible = "fixed-partitions";
356 #address-cells = <1>;
357 #size-cells = <1>;
361 read-only;
365 read-only;
369 read-only;
373 read-only;
377 read-only;
381 read-only;
385 read-only;
387 uboot-env@700000 {
389 read-only;
405 timeout-sec = <60>;
410 pinctrl-0 = <&scif0_pins>;
411 pinctrl-names = "default";
417 clock-frequency = <14745600>;