Lines Matching +full:full +full:- +full:pwr +full:- +full:cycle
1 // SPDX-License-Identifier: GPL-2.0
3 * Device Tree Source for the Ebisu/Ebisu-4D board
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/input.h>
33 stdout-path = "serial0:115200n8";
36 audio_clkout: audio-clkout {
39 * but needed to avoid cs2000/rcar_sound probe dead-lock
41 compatible = "fixed-clock";
42 #clock-cells = <0>;
43 clock-frequency = <11289600>;
47 compatible = "pwm-backlight";
50 brightness-levels = <512 511 505 494 473 440 392 327 241 133 0>;
51 default-brightness-level = <10>;
53 power-supply = <®_12p0v>;
56 cvbs-in {
57 compatible = "composite-video-connector";
62 remote-endpoint = <&adv7482_ain7>;
67 hdmi-in {
68 compatible = "hdmi-connector";
74 remote-endpoint = <&adv7482_hdmi>;
79 hdmi-out {
80 compatible = "hdmi-connector";
85 remote-endpoint = <&adv7511_out>;
91 compatible = "gpio-keys";
93 pinctrl-0 = <&keys_pins>;
94 pinctrl-names = "default";
96 key-1 {
99 label = "SW4-1";
100 wakeup-source;
101 debounce-interval = <20>;
103 key-2 {
106 label = "SW4-2";
107 wakeup-source;
108 debounce-interval = <20>;
110 key-3 {
113 label = "SW4-3";
114 wakeup-source;
115 debounce-interval = <20>;
117 key-4 {
120 label = "SW4-4";
121 wakeup-source;
122 debounce-interval = <20>;
126 lvds-decoder {
128 vcc-supply = <®_3p3v>;
131 #address-cells = <1>;
132 #size-cells = <0>;
137 remote-endpoint = <&lvds0_out>;
144 remote-endpoint = <&adv7511_in>;
156 reg_1p8v: regulator-1p8v {
157 compatible = "regulator-fixed";
158 regulator-name = "fixed-1.8V";
159 regulator-min-microvolt = <1800000>;
160 regulator-max-microvolt = <1800000>;
161 regulator-boot-on;
162 regulator-always-on;
165 reg_3p3v: regulator-3p3v {
166 compatible = "regulator-fixed";
167 regulator-name = "fixed-3.3V";
168 regulator-min-microvolt = <3300000>;
169 regulator-max-microvolt = <3300000>;
170 regulator-boot-on;
171 regulator-always-on;
174 reg_12p0v: regulator-12p0v {
175 compatible = "regulator-fixed";
176 regulator-name = "D12.0V";
177 regulator-min-microvolt = <12000000>;
178 regulator-max-microvolt = <12000000>;
179 regulator-boot-on;
180 regulator-always-on;
184 compatible = "simple-audio-card";
186 simple-audio-card,name = "rsnd-ak4613";
187 simple-audio-card,format = "left_j";
188 simple-audio-card,bitclock-master = <&sndcpu>;
189 simple-audio-card,frame-master = <&sndcpu>;
191 sndcodec: simple-audio-card,codec {
192 sound-dai = <&ak4613>;
195 sndcpu: simple-audio-card,cpu {
196 sound-dai = <&rcar_sound>;
200 vbus0_usb2: regulator-vbus0-usb2 {
201 compatible = "regulator-fixed";
203 regulator-name = "USB20_VBUS_CN";
204 regulator-min-microvolt = <5000000>;
205 regulator-max-microvolt = <5000000>;
208 enable-active-high;
211 vcc_sdhi0: regulator-vcc-sdhi0 {
212 compatible = "regulator-fixed";
214 regulator-name = "SDHI0 Vcc";
215 regulator-min-microvolt = <3300000>;
216 regulator-max-microvolt = <3300000>;
219 enable-active-high;
222 vccq_sdhi0: regulator-vccq-sdhi0 {
223 compatible = "regulator-gpio";
225 regulator-name = "SDHI0 VccQ";
226 regulator-min-microvolt = <1800000>;
227 regulator-max-microvolt = <3300000>;
230 gpios-states = <1>;
234 vcc_sdhi1: regulator-vcc-sdhi1 {
235 compatible = "regulator-fixed";
237 regulator-name = "SDHI1 Vcc";
238 regulator-min-microvolt = <3300000>;
239 regulator-max-microvolt = <3300000>;
242 enable-active-high;
245 vccq_sdhi1: regulator-vccq-sdhi1 {
246 compatible = "regulator-gpio";
248 regulator-name = "SDHI1 VccQ";
249 regulator-min-microvolt = <1800000>;
250 regulator-max-microvolt = <3300000>;
253 gpios-states = <1>;
258 compatible = "vga-connector";
262 remote-endpoint = <&adv7123_out>;
267 vga-encoder {
271 #address-cells = <1>;
272 #size-cells = <0>;
277 remote-endpoint = <&du_out_rgb>;
283 remote-endpoint = <&vga_in>;
290 compatible = "fixed-clock";
291 #clock-cells = <0>;
292 clock-frequency = <24576000>;
296 compatible = "fixed-clock";
297 #clock-cells = <0>;
298 clock-frequency = <74250000>;
303 clock-frequency = <22579200>;
307 pinctrl-0 = <&avb_pins>;
308 pinctrl-names = "default";
309 phy-handle = <&phy0>;
312 phy0: ethernet-phy@0 {
313 compatible = "ethernet-phy-id0022.1622",
314 "ethernet-phy-ieee802.3-c22";
315 rxc-skew-ps = <1500>;
317 interrupts-extended = <&gpio2 21 IRQ_TYPE_LEVEL_LOW>;
318 reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
323 * isn't supported on R-Car E3(e). Thus, limit speed to
326 max-speed = <100>;
331 pinctrl-0 = <&canfd0_pins>;
332 pinctrl-names = "default";
346 clock-lanes = <0>;
347 data-lanes = <1 2>;
348 remote-endpoint = <&adv7482_txa>;
355 pinctrl-0 = <&du_pins>;
356 pinctrl-names = "default";
362 clock-names = "du.0", "du.1", "dclkin.0";
367 remote-endpoint = <&adv7123_in>;
379 clock-frequency = <48000000>;
393 gpio-controller;
394 #gpio-cells = <2>;
395 interrupts-extended = <&gpio2 22 IRQ_TYPE_LEVEL_LOW>;
398 hdmi-encoder@39 {
401 interrupts-extended = <&gpio1 1 IRQ_TYPE_LEVEL_LOW>;
403 avdd-supply = <®_1p8v>;
404 dvdd-supply = <®_1p8v>;
405 pvdd-supply = <®_1p8v>;
406 dvdd-3v-supply = <®_3p3v>;
407 bgvdd-supply = <®_1p8v>;
409 adi,input-depth = <8>;
410 adi,input-colorspace = "rgb";
411 adi,input-clock = "1x";
414 #address-cells = <1>;
415 #size-cells = <0>;
420 remote-endpoint = <&thc63lvd1024_out>;
427 remote-endpoint = <&hdmi_con_out>;
433 video-receiver@70 {
437 interrupts-extended = <&gpio0 7 IRQ_TYPE_LEVEL_LOW>,
439 interrupt-names = "intrq1", "intrq2";
442 #address-cells = <1>;
443 #size-cells = <0>;
449 remote-endpoint = <&cvbs_con>;
457 remote-endpoint = <&hdmi_in_con>;
465 clock-lanes = <0>;
466 data-lanes = <1 2>;
467 remote-endpoint = <&csi40_in>;
478 compatible = "asahi-kasei,ak4613";
479 #sound-dai-cells = <0>;
483 asahi-kasei,in1-single-end;
484 asahi-kasei,in2-single-end;
485 asahi-kasei,out1-single-end;
486 asahi-kasei,out2-single-end;
487 asahi-kasei,out3-single-end;
488 asahi-kasei,out4-single-end;
489 asahi-kasei,out5-single-end;
490 asahi-kasei,out6-single-end;
493 cs2000: clk-multiplier@4f {
494 #clock-cells = <0>;
495 compatible = "cirrus,cs2000-cp";
498 clock-names = "clk_in", "ref_clk";
500 assigned-clocks = <&cs2000>;
501 assigned-clock-rates = <24576000>; /* 1/1 divide */
508 clock-frequency = <400000>;
511 pinctrl-0 = <&irq0_pins>;
512 pinctrl-names = "default";
516 interrupts-extended = <&intc_ex 0 IRQ_TYPE_LEVEL_LOW>;
517 interrupt-controller;
518 #interrupt-cells = <2>;
519 gpio-controller;
520 #gpio-cells = <2>;
521 rohm,ddr-backup-power = <0x1>;
522 rohm,rstbmode-level;
538 clock-names = "fck", "dclkin.0", "extal";
543 remote-endpoint = <&thc63lvd1024_in>;
560 clock-names = "fck", "dclkin.0", "extal";
569 clock-frequency = <100000000>;
599 bias-pull-up;
626 power-source = <3300>;
632 power-source = <1800>;
638 power-source = <3300>;
644 power-source = <1800>;
650 power-source = <1800>;
676 pinctrl-0 = <&pwm3_pins>;
677 pinctrl-names = "default";
683 pinctrl-0 = <&pwm5_pins>;
684 pinctrl-names = "default";
690 pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
691 pinctrl-names = "default";
694 #sound-dai-cells = <0>;
697 #clock-cells = <1>;
698 clock-frequency = <12288000 11289600>;
730 pinctrl-0 = <&rpc_pins>;
731 pinctrl-names = "default";
736 compatible = "cypress,hyperflash", "cfi-flash";
740 compatible = "fixed-partitions";
741 #address-cells = <1>;
742 #size-cells = <1>;
746 read-only;
750 read-only;
754 read-only;
758 read-only;
762 read-only;
766 read-only;
782 timeout-sec = <60>;
787 pinctrl-0 = <&scif2_pins>;
788 pinctrl-names = "default";
794 pinctrl-0 = <&sdhi0_pins>;
795 pinctrl-1 = <&sdhi0_pins_uhs>;
796 pinctrl-names = "default", "state_uhs";
798 vmmc-supply = <&vcc_sdhi0>;
799 vqmmc-supply = <&vccq_sdhi0>;
800 cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
801 wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
802 bus-width = <4>;
803 sd-uhs-sdr50;
804 sd-uhs-sdr104;
809 pinctrl-0 = <&sdhi1_pins>;
810 pinctrl-1 = <&sdhi1_pins_uhs>;
811 pinctrl-names = "default", "state_uhs";
813 vmmc-supply = <&vcc_sdhi1>;
814 vqmmc-supply = <&vccq_sdhi1>;
815 cd-gpios = <&gpio3 14 GPIO_ACTIVE_LOW>;
816 bus-width = <4>;
817 sd-uhs-sdr50;
818 sd-uhs-sdr104;
823 /* used for on-board 8bit eMMC */
824 pinctrl-0 = <&sdhi3_pins>;
825 pinctrl-1 = <&sdhi3_pins>;
826 pinctrl-names = "default", "state_uhs";
828 vmmc-supply = <®_3p3v>;
829 vqmmc-supply = <®_1p8v>;
830 mmc-hs200-1_8v;
831 mmc-hs400-1_8v;
832 bus-width = <8>;
833 no-sd;
834 no-sdio;
835 non-removable;
836 full-pwr-cycle-in-suspend;
841 shared-pin;
845 pinctrl-0 = <&usb0_pins>;
846 pinctrl-names = "default";
848 vbus-supply = <&vbus0_usb2>;
866 pinctrl-0 = <&usb30_pins>;
867 pinctrl-names = "default";