Lines Matching +full:ath11k +full:- +full:calibration +full:- +full:variant
1 // SPDX-License-Identifier: BSD-3-Clause
9 /dts-v1/;
11 #include <dt-bindings/iio/qcom,spmi-adc7-pm8350.h>
12 #include <dt-bindings/gpio/gpio.h>
13 #include <dt-bindings/input/gpio-keys.h>
14 #include <dt-bindings/input/input.h>
15 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
18 #include "sc8280xp-pmics.dtsi"
23 chassis-type = "desktop";
31 wcd938x: audio-codec {
32 compatible = "qcom,wcd9380-codec";
34 pinctrl-0 = <&wcd_default>;
35 pinctrl-names = "default";
37 reset-gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
39 vdd-buck-supply = <&vreg_s10b>;
40 vdd-rxtx-supply = <&vreg_s10b>;
41 vdd-io-supply = <&vreg_s10b>;
42 vdd-mic-bias-supply = <&vreg_bob>;
44 qcom,micbias1-microvolt = <1800000>;
45 qcom,micbias2-microvolt = <1800000>;
46 qcom,micbias3-microvolt = <1800000>;
47 qcom,micbias4-microvolt = <1800000>;
48 qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
49 qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
50 qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
51 qcom,rx-device = <&wcd_rx>;
52 qcom,tx-device = <&wcd_tx>;
54 #sound-dai-cells = <1>;
58 compatible = "dp-connector";
59 label = "DP-3";
62 dp-pwr-supply = <&vreg_misc_3p3>;
66 remote-endpoint = <&mdss0_dp2_phy_out>;
71 pmic-glink {
72 compatible = "qcom,sc8280xp-pmic-glink", "qcom,pmic-glink";
74 #address-cells = <1>;
75 #size-cells = <0>;
76 orientation-gpios = <&tlmm 166 GPIO_ACTIVE_HIGH>,
79 /* Left-side rear port */
81 compatible = "usb-c-connector";
83 power-role = "source";
84 data-role = "dual";
87 #address-cells = <1>;
88 #size-cells = <0>;
94 remote-endpoint = <&usb_0_dwc3_hs>;
102 remote-endpoint = <&usb_0_qmpphy_out>;
110 remote-endpoint = <&usb0_sbu_mux>;
116 /* Left-side front port */
118 compatible = "usb-c-connector";
120 power-role = "source";
121 data-role = "dual";
124 #address-cells = <1>;
125 #size-cells = <0>;
131 remote-endpoint = <&usb_1_dwc3_hs>;
139 remote-endpoint = <&usb_1_qmpphy_out>;
147 remote-endpoint = <&usb1_sbu_mux>;
154 vreg_misc_3p3: regulator-misc-3p3 {
155 compatible = "regulator-fixed";
157 regulator-name = "VCC3B";
158 regulator-min-microvolt = <3300000>;
159 regulator-max-microvolt = <3300000>;
162 enable-active-high;
164 pinctrl-0 = <&misc_3p3_reg_en>;
165 pinctrl-names = "default";
167 regulator-boot-on;
168 regulator-always-on;
171 vreg_nvme: regulator-nvme {
172 compatible = "regulator-fixed";
174 regulator-name = "VCC3_SSD";
175 regulator-min-microvolt = <3300000>;
176 regulator-max-microvolt = <3300000>;
179 enable-active-high;
181 pinctrl-0 = <&nvme_reg_en>;
182 pinctrl-names = "default";
184 regulator-boot-on;
187 vreg_vph_pwr: regulator-vph-pwr {
188 compatible = "regulator-fixed";
190 regulator-name = "VPH_VCC3R9";
191 regulator-min-microvolt = <3900000>;
192 regulator-max-microvolt = <3900000>;
194 regulator-always-on;
197 vreg_wlan: regulator-wlan {
198 compatible = "regulator-fixed";
200 regulator-name = "VCC_WLAN_3R9";
201 regulator-min-microvolt = <3900000>;
202 regulator-max-microvolt = <3900000>;
205 enable-active-high;
207 pinctrl-0 = <&hastings_reg_en>;
208 pinctrl-names = "default";
210 regulator-boot-on;
213 vreg_wwan: regulator-wwan {
214 compatible = "regulator-fixed";
216 regulator-name = "VCC3B_WAN";
217 regulator-min-microvolt = <3300000>;
218 regulator-max-microvolt = <3300000>;
221 enable-active-high;
223 pinctrl-0 = <&wwan_sw_en>;
224 pinctrl-names = "default";
226 regulator-boot-on;
229 reserved-memory {
230 gpu_mem: gpu-mem@8bf00000 {
232 no-map;
236 compatible = "shared-dma-pool";
239 linux,cma-default;
243 usb0-sbu-mux {
244 compatible = "pericom,pi3usb102", "gpio-sbu-mux";
246 enable-gpios = <&tlmm 101 GPIO_ACTIVE_LOW>;
247 select-gpios = <&tlmm 164 GPIO_ACTIVE_HIGH>;
249 pinctrl-0 = <&usb0_sbu_default>;
250 pinctrl-names = "default";
252 mode-switch;
253 orientation-switch;
257 remote-endpoint = <&pmic_glink_con0_sbu>;
262 usb1-sbu-mux {
263 compatible = "pericom,pi3usb102", "gpio-sbu-mux";
265 enable-gpios = <&tlmm 48 GPIO_ACTIVE_LOW>;
266 select-gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>;
268 pinctrl-0 = <&usb1_sbu_default>;
269 pinctrl-names = "default";
271 mode-switch;
272 orientation-switch;
276 remote-endpoint = <&pmic_glink_con1_sbu>;
281 wcn6855-pmu {
282 compatible = "qcom,wcn6855-pmu";
284 pinctrl-0 = <&bt_default>, <&wlan_en>;
285 pinctrl-names = "default";
287 wlan-enable-gpios = <&tlmm 134 GPIO_ACTIVE_HIGH>;
288 bt-enable-gpios = <&tlmm 133 GPIO_ACTIVE_HIGH>;
289 swctrl-gpios = <&tlmm 132 GPIO_ACTIVE_HIGH>;
291 vddio-supply = <&vreg_s10b>;
292 vddaon-supply = <&vreg_s12b>;
293 vddpmu-supply = <&vreg_s12b>;
294 vddpmumx-supply = <&vreg_s12b>;
295 vddpmucx-supply = <&vreg_s12b>;
296 vddrfa0p95-supply = <&vreg_s12b>;
297 vddrfa1p3-supply = <&vreg_s11b>;
298 vddrfa1p9-supply = <&vreg_s1c>;
299 vddpcie1p3-supply = <&vreg_s11b>;
300 vddpcie1p9-supply = <&vreg_s1c>;
304 regulator-name = "vreg_pmu_rfa_cmn_0p8";
308 regulator-name = "vreg_pmu_aon_0p8";
312 regulator-name = "vreg_pmu_wlcx_0p8";
316 regulator-name = "vreg_pmu_wlmx_0p8";
320 regulator-name = "vreg_pmu_btcmx_0p8";
324 regulator-name = "vreg_pmu_pcie_1p8";
328 regulator-name = "vreg_pmu_pcie_0p9";
332 regulator-name = "vreg_pmu_rfa_0p8";
336 regulator-name = "vreg_pmu_rfa_1p2";
340 regulator-name = "vreg_pmu_rfa_1p7";
347 regulators-0 {
348 compatible = "qcom,pm8350-rpmh-regulators";
349 qcom,pmic-id = "b";
351 vdd-s10-supply = <&vreg_vph_pwr>;
352 vdd-s11-supply = <&vreg_vph_pwr>;
353 vdd-s12-supply = <&vreg_vph_pwr>;
354 vdd-l1-l4-supply = <&vreg_s12b>;
355 vdd-l2-l7-supply = <&vreg_bob>;
356 vdd-l3-l5-supply = <&vreg_s11b>;
357 vdd-l6-l9-l10-supply = <&vreg_s12b>;
358 vdd-l8-supply = <&vreg_s12b>;
361 regulator-name = "vreg_s10b";
362 regulator-min-microvolt = <1800000>;
363 regulator-max-microvolt = <1800000>;
364 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
365 regulator-always-on;
369 regulator-name = "vreg_s11b";
370 regulator-min-microvolt = <1272000>;
371 regulator-max-microvolt = <1272000>;
372 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
376 regulator-name = "vreg_s12b";
377 regulator-min-microvolt = <984000>;
378 regulator-max-microvolt = <984000>;
379 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
383 regulator-name = "vreg_l1b";
384 regulator-min-microvolt = <912000>;
385 regulator-max-microvolt = <912000>;
386 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
390 regulator-name = "vreg_l3b";
391 regulator-min-microvolt = <1200000>;
392 regulator-max-microvolt = <1200000>;
393 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
394 regulator-boot-on;
398 regulator-name = "vreg_l4b";
399 regulator-min-microvolt = <912000>;
400 regulator-max-microvolt = <912000>;
401 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
405 regulator-name = "vreg_l6b";
406 regulator-min-microvolt = <880000>;
407 regulator-max-microvolt = <880000>;
408 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
409 regulator-boot-on;
413 regulators-1 {
414 compatible = "qcom,pm8350c-rpmh-regulators";
415 qcom,pmic-id = "c";
417 vdd-bob-supply = <&vreg_vph_pwr>;
418 vdd-l1-l12-supply = <&vreg_s1c>;
419 vdd-l2-l8-supply = <&vreg_s1c>;
420 vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>;
421 vdd-l6-l9-l11-supply = <&vreg_bob>;
422 vdd-l10-supply = <&vreg_s11b>;
425 regulator-name = "vreg_s1c";
426 regulator-min-microvolt = <1880000>;
427 regulator-max-microvolt = <1900000>;
428 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
429 regulator-always-on;
433 regulator-name = "vreg_l1c";
434 regulator-min-microvolt = <1800000>;
435 regulator-max-microvolt = <1800000>;
436 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
440 regulator-name = "vreg_l6c";
441 regulator-min-microvolt = <1800000>;
442 regulator-max-microvolt = <2960000>;
443 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
447 regulator-name = "vreg_l7c";
448 regulator-min-microvolt = <2504000>;
449 regulator-max-microvolt = <2504000>;
450 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
451 regulator-allow-set-load;
452 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
457 regulator-name = "vreg_l8c";
458 regulator-min-microvolt = <1800000>;
459 regulator-max-microvolt = <1800000>;
460 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
464 regulator-name = "vreg_l9c";
465 regulator-min-microvolt = <2960000>;
466 regulator-max-microvolt = <2960000>;
467 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
471 regulator-name = "vreg_l12c";
472 regulator-min-microvolt = <1800000>;
473 regulator-max-microvolt = <1800000>;
474 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
478 regulator-name = "vreg_l13c";
479 regulator-min-microvolt = <3072000>;
480 regulator-max-microvolt = <3072000>;
481 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
485 regulator-name = "vreg_bob";
486 regulator-min-microvolt = <3008000>;
487 regulator-max-microvolt = <3960000>;
488 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
489 regulator-always-on;
493 regulators-2 {
494 compatible = "qcom,pm8350-rpmh-regulators";
495 qcom,pmic-id = "d";
497 vdd-l1-l4-supply = <&vreg_s11b>;
498 vdd-l2-l7-supply = <&vreg_bob>;
499 vdd-l3-l5-supply = <&vreg_s11b>;
500 vdd-l6-l9-l10-supply = <&vreg_s12b>;
501 vdd-l8-supply = <&vreg_s12b>;
504 regulator-name = "vreg_l2d";
505 regulator-min-microvolt = <3072000>;
506 regulator-max-microvolt = <3072000>;
507 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
511 regulator-name = "vreg_l3d";
512 regulator-min-microvolt = <1200000>;
513 regulator-max-microvolt = <1200000>;
514 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
515 regulator-allow-set-load;
516 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
521 regulator-name = "vreg_l4d";
522 regulator-min-microvolt = <1200000>;
523 regulator-max-microvolt = <1200000>;
524 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
528 regulator-name = "vreg_l6d";
529 regulator-min-microvolt = <880000>;
530 regulator-max-microvolt = <880000>;
531 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
535 regulator-name = "vreg_l7d";
536 regulator-min-microvolt = <3072000>;
537 regulator-max-microvolt = <3072000>;
538 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
542 regulator-name = "vreg_l8d";
543 regulator-min-microvolt = <912000>;
544 regulator-max-microvolt = <912000>;
545 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
549 regulator-name = "vreg_l9d";
550 regulator-min-microvolt = <912000>;
551 regulator-max-microvolt = <912000>;
552 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
556 regulator-name = "vreg_l10d";
557 regulator-min-microvolt = <912000>;
558 regulator-max-microvolt = <912000>;
559 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
571 zap-shader {
572 memory-region = <&gpu_mem>;
573 firmware-name = "qcom/sc8280xp/microsoft/blackrock/qcdxkmsuc8280.mbn";
586 data-lanes = <0 1>;
587 remote-endpoint = <&usb_0_qmpphy_dp_in>;
595 data-lanes = <0 1>;
596 remote-endpoint = <&usb_1_qmpphy_dp_in>;
600 compatible = "qcom,sc8280xp-dp";
602 data-lanes = <0 1 2 3>;
610 remote-endpoint = <&dp1_connector_in>;
617 compatible = "qcom,sc8280xp-dp-phy";
619 vdda-phy-supply = <&vreg_l3b>;
620 vdda-pll-supply = <&vreg_l6b>;
626 perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
627 wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
629 vddpe-3v3-supply = <&vreg_nvme>;
631 pinctrl-0 = <&pcie2a_default>;
632 pinctrl-names = "default";
638 vdda-phy-supply = <&vreg_l4d>;
639 vdda-pll-supply = <&vreg_l6d>;
645 max-link-speed = <2>;
647 perst-gpios = <&tlmm 141 GPIO_ACTIVE_LOW>;
648 wake-gpios = <&tlmm 139 GPIO_ACTIVE_LOW>;
650 vddpe-3v3-supply = <&vreg_wlan>;
652 pinctrl-0 = <&pcie4_default>;
653 pinctrl-names = "default";
663 vddrfacmn-supply = <&vreg_pmu_rfa_cmn_0p8>;
664 vddaon-supply = <&vreg_pmu_aon_0p8>;
665 vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
666 vddwlmx-supply = <&vreg_pmu_wlmx_0p8>;
667 vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
668 vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
669 vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
670 vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
671 vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
673 qcom,ath11k-calibration-variant = "MS_Volterra";
678 vdda-phy-supply = <&vreg_l4d>;
679 vdda-pll-supply = <&vreg_l6d>;
691 sys-therm@0 {
693 io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM1_100K_PU(1)>;
694 qcom,hw-settle-time-us = <200>;
695 qcom,avg-samples = <2>;
699 sys-therm@1 {
701 io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM2_100K_PU(1)>;
702 qcom,hw-settle-time-us = <200>;
703 qcom,avg-samples = <2>;
707 sys-therm@2 {
709 io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM3_100K_PU(1)>;
710 qcom,hw-settle-time-us = <200>;
711 qcom,avg-samples = <2>;
715 sys-therm@3 {
717 io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM4_100K_PU(1)>;
718 qcom,hw-settle-time-us = <200>;
719 qcom,avg-samples = <2>;
723 sys-therm@4 {
725 io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM1_100K_PU(3)>;
726 qcom,hw-settle-time-us = <200>;
727 qcom,avg-samples = <2>;
731 sys-therm@5 {
733 io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM2_100K_PU(3)>;
734 qcom,hw-settle-time-us = <200>;
735 qcom,avg-samples = <2>;
739 sys-therm@6 {
741 io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM3_100K_PU(3)>;
742 qcom,hw-settle-time-us = <200>;
743 qcom,avg-samples = <2>;
747 sys-therm@7 {
749 io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM4_100K_PU(3)>;
750 qcom,hw-settle-time-us = <200>;
751 qcom,avg-samples = <2>;
765 nvmem-cells = <&rtc_offset>;
766 nvmem-cell-names = "offset";
774 rtc_offset: rtc-offset@bc {
782 qcom,hw-settle-time = <200>;
789 qcom,hw-settle-time = <200>;
796 qcom,hw-settle-time = <200>;
803 qcom,hw-settle-time = <200>;
810 qcom,hw-settle-time = <200>;
817 qcom,hw-settle-time = <200>;
824 qcom,hw-settle-time = <200>;
831 qcom,hw-settle-time = <200>;
850 firmware-name = "qcom/sc8280xp/microsoft/blackrock/qcadsp8280.mbn";
856 firmware-name = "qcom/sc8280xp/microsoft/blackrock/qccdsp8280.mbn";
866 compatible = "qcom,sc8280xp-sndcard";
869 wcd-playback-dai-link {
870 link-name = "WCD Playback";
873 sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
877 sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>;
881 sound-dai = <&q6apm>;
885 wcd-capture-dai-link {
886 link-name = "WCD Capture";
889 sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
893 sound-dai = <&wcd938x 1>, <&swr2 0>, <&txmacro 0>;
897 sound-dai = <&q6apm>;
901 wsa-dai-link {
902 link-name = "WSA Playback";
905 sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
909 sound-dai = <&swr0 0>, <&wsamacro 0>;
913 sound-dai = <&q6apm>;
917 va-dai-link {
918 link-name = "VA Capture";
921 sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
925 sound-dai = <&q6apm>;
929 sound-dai = <&vamacro 0>;
941 wcd_rx: wcd9380-rx@0,4 {
944 qcom,rx-port-mapping = <1 2 3 4 5>;
951 wcd_tx: wcd9380-tx@0,3 {
954 qcom,tx-port-mapping = <1 1 2 3>;
963 pinctrl-0 = <&uart2_default>;
964 pinctrl-names = "default";
969 compatible = "qcom,wcn6855-bt";
971 vddrfacmn-supply = <&vreg_pmu_rfa_cmn_0p8>;
972 vddaon-supply = <&vreg_pmu_aon_0p8>;
973 vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
974 vddwlmx-supply = <&vreg_pmu_wlmx_0p8>;
975 vddbtcmx-supply = <&vreg_pmu_btcmx_0p8>;
976 vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
977 vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
978 vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
980 max-speed = <3200000>;
993 remote-endpoint = <&pmic_glink_con0_hs>;
997 vdda-pll-supply = <&vreg_l9d>;
998 vdda18-supply = <&vreg_l1c>;
999 vdda33-supply = <&vreg_l7d>;
1005 vdda-phy-supply = <&vreg_l4d>;
1006 vdda-pll-supply = <&vreg_l9d>;
1008 orientation-switch;
1014 remote-endpoint = <&mdss0_dp0_out>;
1018 remote-endpoint = <&pmic_glink_con0_ss>;
1030 remote-endpoint = <&pmic_glink_con1_hs>;
1034 vdda-pll-supply = <&vreg_l4b>;
1035 vdda18-supply = <&vreg_l1c>;
1036 vdda33-supply = <&vreg_l13c>;
1042 vdda-phy-supply = <&vreg_l3b>;
1043 vdda-pll-supply = <&vreg_l4b>;
1045 orientation-switch;
1051 remote-endpoint = <&mdss0_dp1_out>;
1055 remote-endpoint = <&pmic_glink_con1_ss>;
1059 pinctrl-0 = <&usb2_en_state>;
1060 pinctrl-names = "default";
1067 phy-names = "usb2-0", "usb3-0";
1071 vdda-pll-supply = <&vreg_l1b>;
1072 vdda18-supply = <&vreg_l1c>;
1073 vdda33-supply = <&vreg_l7d>;
1079 vdda-phy-supply = <&vreg_l1b>;
1080 vdda-pll-supply = <&vreg_l4d>;
1086 pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
1087 pinctrl-names = "default";
1089 vdd-micb-supply = <&vreg_s10b>;
1091 qcom,dmic-sample-rate = <4800000>;
1101 clock-frequency = <38400000>;
1111 misc_3p3_reg_en: misc-3p3-reg-en-state {
1116 edp_bl_en: edp-bl-en-state {
1121 edp_bl_reg_en: edp-bl-reg-en-state {
1128 wwan_sw_en: wwan-sw-en-state {
1135 edp_bl_pwm: edp-bl-pwm-state {
1142 hastings_reg_en: hastings-reg-en-state {
1149 bt_default: bt-default-state {
1150 hstp-bt-en-pins {
1153 drive-strength = <16>;
1154 bias-disable;
1157 hstp-sw-ctrl-pins {
1160 bias-pull-down;
1164 nvme_reg_en: nvme-reg-en-state {
1167 drive-strength = <2>;
1168 bias-disable;
1171 pcie2a_default: pcie2a-default-state {
1172 clkreq-n-pins {
1175 drive-strength = <2>;
1176 bias-pull-up;
1179 perst-n-pins {
1182 drive-strength = <2>;
1183 bias-disable;
1186 wake-n-pins {
1189 drive-strength = <2>;
1190 bias-pull-up;
1194 pcie3a_default: pcie3a-default-state {
1195 clkreq-n-pins {
1198 drive-strength = <2>;
1199 bias-pull-up;
1202 perst-n-pins {
1205 drive-strength = <2>;
1206 bias-disable;
1209 wake-n-pins {
1212 drive-strength = <2>;
1213 bias-pull-up;
1217 pcie4_default: pcie4-default-state {
1218 clkreq-n-pins {
1221 drive-strength = <2>;
1222 bias-pull-up;
1225 perst-n-pins {
1228 drive-strength = <2>;
1229 bias-disable;
1232 wake-n-pins {
1235 drive-strength = <2>;
1236 bias-pull-up;
1240 uart2_default: uart2-default-state {
1241 cts-pins {
1244 bias-bus-hold;
1247 rts-pins {
1250 drive-strength = <2>;
1251 bias-disable;
1254 rx-pins {
1257 bias-pull-up;
1260 tx-pins {
1263 drive-strength = <2>;
1264 bias-disable;
1268 usb0_sbu_default: usb0-sbu-state {
1269 oe-n-pins {
1272 bias-disable;
1273 drive-strength = <16>;
1274 output-high;
1277 sel-pins {
1280 bias-disable;
1281 drive-strength = <16>;
1285 usb1_sbu_default: usb1-sbu-state {
1286 oe-n-pins {
1289 bias-disable;
1290 drive-strength = <16>;
1291 output-high;
1294 sel-pins {
1297 bias-disable;
1298 drive-strength = <16>;
1302 usb2_en_state: usb2-en-state {
1306 drive-strength = <2>;
1307 bias-disable;
1308 output-low;
1311 wcd_default: wcd-default-state {
1312 reset-pins {
1315 bias-disable;
1319 wlan_en: wlan-en-state {
1322 drive-strength = <8>;
1323 bias-pull-down;