Lines Matching +full:0 +full:- +full:pwrkey

1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
4 #include <dt-bindings/iio/qcom,spmi-vadc.h>
5 #include <dt-bindings/input/linux-event-codes.h>
6 #include <dt-bindings/interrupt-controller/irq.h>
7 #include <dt-bindings/spmi/spmi.h>
8 #include <dt-bindings/thermal/thermal.h>
11 	thermal-zones {
12 		pm8998-thermal {
13 			polling-delay-passive = <250>;
15 			thermal-sensors = <&pm8998_temp>;
18 				pm8998_alert0: pm8998-alert0 {
23 				pm8998_crit: pm8998-crit {
34 	pm8998_lsid0: pmic@0 {
35 		compatible = "qcom,pm8998", "qcom,spmi-pmic";
36 		reg = <0x0 SPMI_USID>;
37 		#address-cells = <1>;
38 		#size-cells = <0>;
41 			compatible = "qcom,pm8998-pon";
43 			reg = <0x800>;
44 			mode-bootloader = <0x2>;
45 			mode-recovery = <0x1>;
47 			pm8998_pwrkey: pwrkey {
48 				compatible = "qcom,pm8941-pwrkey";
49 				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
51 				bias-pull-up;
56 				compatible = "qcom,pm8941-resin";
57 				interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
59 				bias-pull-up;
64 		pm8998_temp: temp-alarm@2400 {
65 			compatible = "qcom,spmi-temp-alarm";
66 			reg = <0x2400>;
67 			interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
68 			io-channels = <&pm8998_adc ADC5_DIE_TEMP>;
69 			io-channel-names = "thermal";
70 			#thermal-sensor-cells = <0>;
74 			compatible = "qcom,pm8998-coincell", "qcom,pm8941-coincell";
75 			reg = <0x2800>;
81 			compatible = "qcom,spmi-adc-rev2";
82 			reg = <0x3100>;
83 			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
84 			#address-cells = <1>;
85 			#size-cells = <0>;
86 			#io-channel-cells = <1>;
94 		pm8998_adc_tm: adc-tm@3400 {
95 			compatible = "qcom,spmi-adc-tm-hc";
96 			reg = <0x3400>;
97 			interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
98 			#thermal-sensor-cells = <1>;
99 			#address-cells = <1>;
100 			#size-cells = <0>;
105 			compatible = "qcom,pm8941-rtc";
106 			reg = <0x6000>, <0x6100>;
107 			reg-names = "rtc", "alarm";
108 			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
112 			compatible = "qcom,pm8998-gpio", "qcom,spmi-gpio";
113 			reg = <0xc000>;
114 			gpio-controller;
115 			gpio-ranges = <&pm8998_gpios 0 0 26>;
116 			#gpio-cells = <2>;
117 			interrupt-controller;
118 			#interrupt-cells = <2>;
124 		compatible = "qcom,pm8998", "qcom,spmi-pmic";
125 		reg = <0x1 SPMI_USID>;
126 		#address-cells = <1>;
127 		#size-cells = <0>;