Lines Matching +full:srp +full:- +full:disable
1 // SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
3 * Copyright 2020-2021 TQ-Systems GmbH
6 /dts-v1/;
8 #include <dt-bindings/phy/phy-imx8-pcie.h>
10 #include "imx8mm-tqma8mqml.dtsi"
14 model = "TQ-Systems GmbH i.MX8MM TQMa8MxML on MBa8Mx";
15 compatible = "tq,imx8mm-tqma8mqml-mba8mx", "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
16 chassis-type = "embedded";
27 reg_usdhc2_vmmc: regulator-vmmc {
28 compatible = "regulator-fixed";
29 pinctrl-names = "default";
30 pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
31 regulator-name = "VSD_3V3";
32 regulator-min-microvolt = <3300000>;
33 regulator-max-microvolt = <3300000>;
35 enable-active-high;
36 startup-delay-us = <100>;
37 off-on-delay-us = <12000>;
41 compatible = "gpio-usb-b-connector", "usb-b-connector";
44 pinctrl-names = "default";
45 pinctrl-0 = <&pinctrl_usb1_connector>;
46 id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
49 #address-cells = <1>;
50 #size-cells = <0>;
55 remote-endpoint = <&usb1_drd_sw>;
66 gpio-controller;
67 #gpio-cells = <2>;
68 vcc-supply = <®_vcc_3v3>;
69 pinctrl-names = "default";
70 pinctrl-0 = <&pinctrl_expander>;
71 interrupt-parent = <&gpio1>;
73 interrupt-controller;
74 #interrupt-cells = <2>;
79 samsung,burst-clock-frequency = <891000000>;
80 samsung,esc-clock-frequency = <20000000>;
84 fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
85 fsl,clkreq-unsupported;
87 clock-names = "ref";
93 reset-gpio = <&expander0 14 GPIO_ACTIVE_LOW>;
96 assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
98 assigned-clock-rates = <10000000>, <250000000>;
99 assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
105 assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
106 assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
107 clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
115 clock-names = "mclk";
120 assigned-clocks = <&clk IMX8MM_CLK_UART1>;
121 assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
125 assigned-clocks = <&clk IMX8MM_CLK_UART2>;
126 assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
130 pinctrl-names = "default";
131 pinctrl-0 = <&pinctrl_usbotg1>;
133 srp-disable;
134 hnp-disable;
135 adp-disable;
136 power-active-high;
137 over-current-active-low;
138 usb-role-switch;
143 remote-endpoint = <&usb_dr_connector>;
150 disable-over-current;
151 vbus-supply = <®_hub_vbus>;
265 pinctrl_usb1_connector: usb1-connectorgrp {
283 pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
293 pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {