Lines Matching +full:technical +full:- +full:documentation
1 # SPDX-License-Identifier: GPL-2.0
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Michael Hennerich <[email protected]>
14 https://www.analog.com/media/en/technical-documentation/data-sheets/AD7605-4.pdf
15 https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606_7606-6_7606-4.pdf
16 https://www.analog.com/media/en/technical-documentation/data-sheets/AD7606B.pdf
17 https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606c-16.pdf
18 https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606c-18.pdf
19 https://www.analog.com/media/en/technical-documentation/data-sheets/ad7607.pdf
20 https://www.analog.com/media/en/technical-documentation/data-sheets/ad7608.pdf
21 https://www.analog.com/media/en/technical-documentation/data-sheets/ad7609.pdf
22 https://www.analog.com/media/en/technical-documentation/data-sheets/AD7616.pdf
27 - adi,ad7605-4
28 - adi,ad7606-4
29 - adi,ad7606-6
30 - adi,ad7606-8 # Referred to as AD7606 (without -8) in the datasheet
31 - adi,ad7606b
32 - adi,ad7606c-16
33 - adi,ad7606c-18
34 - adi,ad7607
35 - adi,ad7608
36 - adi,ad7609
37 - adi,ad7616
42 "#address-cells":
45 "#size-cells":
52 # interface is used, the correct way is to only set spi-cpol.
53 spi-cpha: true
55 spi-cpol: true
57 avcc-supply: true
59 vdrive-supply:
64 refin-supply:
74 adi,conversion-start-gpios:
82 reset-gpios:
90 standby-gpios:
93 place the AD7606 into one of two power-down modes, Standby mode or
98 adi,first-data-gpios:
106 adi,range-gpios:
119 adi,oversampling-ratio-gpios:
121 Must be the device tree identifier of the over-sampling mode pins. As the
127 adi,sw-mode:
133 registers. If the adi,oversampling-ratio-gpios property is defined, then
148 pwm-names:
151 - const: convst1
152 - const: convst2
154 io-backends:
156 A reference to the iio-backend, which is responsible handling the BUSY
163 "^channel@[1-8]$":
175 diff-channels:
180 both positive and negative inputs (i.e. diff-channels = <reg reg>).
190 * Bipolar single-ended
191 * Unipolar single-ended
194 'unipolar single-ended'. So for the other configurations the 'bipolar'
195 property must be specified. If 'diff-channels' is specified, it is
197 single-ended.
200 - reg
201 - bipolar
204 - compatible
205 - reg
206 - avcc-supply
207 - vdrive-supply
210 - $ref: /schemas/spi/spi-peripheral-props.yaml#
212 - oneOf:
213 - required:
214 - adi,conversion-start-gpios
215 - required:
216 - pwms
218 - oneOf:
219 - required:
220 - interrupts
221 - required:
222 - io-backends
224 - if:
231 adi,first-data-gpios: false
232 standby-gpios: false
233 adi,range-gpios:
237 adi,range-gpios:
240 - if:
245 - adi,ad7605-4
246 - adi,ad7616
249 adi,oversampling-ratio-gpios: false
251 - if:
256 - adi,ad7605-4
257 - adi,ad7606-4
258 - adi,ad7606-6
259 - adi,ad7606-8
260 - adi,ad7607
261 - adi,ad7608
262 - adi,ad7609
265 adi,sw-mode: false
270 pwm-names:
272 adi,conversion-start-gpios:
275 - if:
278 - adi,sw-mode
281 "^channel@[1-8]$": false
283 - if:
288 - adi,ad7606c-16
289 - adi,ad7606c-18
292 "^channel@[1-8]$": false
297 - |
298 #include <dt-bindings/gpio/gpio.h>
299 iio-backend {
300 #address-cells = <1>;
301 #size-cells = <0>;
307 avcc-supply = <&adc_vref>;
308 vdrive-supply = <&vdd_supply>;
310 reset-gpios = <&gpio0 91 GPIO_ACTIVE_HIGH>;
311 standby-gpios = <&gpio0 90 GPIO_ACTIVE_LOW>;
312 adi,range-gpios = <&gpio0 89 GPIO_ACTIVE_HIGH>;
313 adi,oversampling-ratio-gpios = <&gpio0 88 GPIO_ACTIVE_HIGH
316 io-backends = <&iio_backend>;
320 - |
321 #include <dt-bindings/gpio/gpio.h>
322 #include <dt-bindings/interrupt-controller/irq.h>
324 #address-cells = <1>;
325 #size-cells = <0>;
328 compatible = "adi,ad7606-8";
330 spi-max-frequency = <1000000>;
331 spi-cpol;
333 avcc-supply = <&adc_vref>;
334 vdrive-supply = <&vdd_supply>;
337 interrupt-parent = <&gpio>;
339 adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
340 reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
341 adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
342 adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH>,
345 standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
348 - |
349 #include <dt-bindings/gpio/gpio.h>
350 #include <dt-bindings/interrupt-controller/irq.h>
352 #address-cells = <1>;
353 #size-cells = <0>;
356 compatible = "adi,ad7606c-18";
359 #address-cells = <1>;
360 #size-cells = <0>;
362 spi-max-frequency = <1000000>;
363 spi-cpol;
365 avcc-supply = <&adc_vref>;
366 vdrive-supply = <&vdd_supply>;
369 interrupt-parent = <&gpio>;
371 adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
372 reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
373 adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
374 standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
376 adi,sw-mode;
380 diff-channels = <1 1>;
391 diff-channels = <8 8>;