Lines Matching +full:sink +full:- +full:vdos
1 # SPDX-License-Identifier: GPL-2.0-only
3 ---
4 $id: http://devicetree.org/schemas/connector/usb-connector.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Rob Herring <[email protected]>
20 - enum:
21 - usb-a-connector
22 - usb-b-connector
23 - usb-c-connector
25 - items:
26 - const: gpio-usb-b-connector
27 - const: usb-b-connector
29 - items:
30 - const: samsung,usb-connector-11pin
31 - const: usb-b-connector
41 non-fullsize 'usb-a-connector' or 'usb-b-connector' compatible
46 - mini
47 - micro
49 self-powered:
53 # The following are optional properties for "usb-b-connector".
54 id-gpios:
58 vbus-gpios:
63 vbus-supply:
67 model it as a regulator. See bindings/regulator/fixed-regulator.yaml
69 power-role:
75 - source
76 - sink
77 - dual
79 try-power-role:
84 - source
85 - sink
86 - dual
88 data-role:
94 - host
95 - device
96 - dual
98 typec-power-opmode:
102 - "default" corresponds to default USB voltage and current defined by the
104 5V 900mA or 1500mA for USB 3.2 ports in single-lane or dual-lane
106 - "1.5A" and "3.0A", 5V 1.5A and 5V 3.0A respectively, as defined in USB
107 Type-C Cable and Connector specification, when Power Delivery is not
111 - default
112 - 1.5A
113 - 3.0A
115 pd-disable:
116 description: Set this property if the Type-C connector has no power delivery support.
119 # The following are optional properties for "usb-c-connector" with power
121 sink-vdos:
125 "USB Power Delivery Specification Revision 3.0, Version 2.0 + ECNs 2020-12-10"
128 dt-bindings/usb/pd.h.
131 $ref: /schemas/types.yaml#/definitions/uint32-array
133 sink-vdos-v1:
139 dt-bindings/usb/pd.h.
142 $ref: /schemas/types.yaml#/definitions/uint32-array
144 accessory-mode-audio:
150 accessory-mode-debug:
169 A single USB-C Alternative Mode as supported by the USB-C connector logic.
176 description: Unique value assigned by USB-IF to the Vendor / AltMode.
207 description: Sideband Use (SBU), present in USB-C. This describes the
211 - port@0
213 new-source-frs-typec-current:
215 is applied during PD3.0 Fast Role Swap. "Table 6-14 Fixed Supply PDO - Sink"
217 different power levels and "6.4.1.3.1.6 Fast Role Swap USB Type-C Current"
218 provides a detailed description of the field. The sink PDO from current source
220 requirement during fr swap. The current sink (i.e. receiver of the FRS signal),
222 new sink's, requirement during frswap before enabling the frs signal reception.
223 This property refers to maximum current capability that the current sink can
226 "1" refers to default USB power level as described by "Table 6-14 Fixed Supply PDO - Sink".
232 slow-charger-loop:
234 still comply to pSnkStby i.e Maximum power that can be consumed by sink while in Sink Standby
235 state as defined in 7.4.2 Sink Electrical Parameters of USB Power Delivery Specification
236 Revision 3.0, Version 1.2. When the property is set, the port requests pSnkStby(2.5W -
239 SNK_READY for non-pd link.
247 "^caps-[0-9]+$":
256 sink-wait-cap-time-ms:
257 description: Represents the max time in ms that USB Type-C port (in sink
259 SinkWaitCap timer starts when port in sink role attaches to the source.
260 This timer will stop when sink receives PD source cap advertisement before
267 ps-source-off-time-ms:
270 timer starts when a sink's PHY layer receives EOP of the GoodCRC message
274 layer. A timeout shall lead to error recovery in the type-c port.
279 cc-debounce-time-ms:
286 sink-bc12-completion-time-ms:
287 description: Represents the max time in ms that a port in sink role takes
290 parallel once the Type-C connection state machine reaches the "potential
291 connect as sink" state. In TCPCs where this causes delays to respond to
292 the incoming PD messages, sink-bc12-completion-time-ms is used to delay
296 pd-revision:
300 $ref: /schemas/types.yaml#/definitions/uint8-array
304 sink-vdos-v1: [ sink-vdos ]
305 sink-vdos: [ sink-vdos-v1 ]
308 - compatible
315 source-pdos:
322 defined in dt-bindings/usb/pd.h.
325 $ref: /schemas/types.yaml#/definitions/uint32-array
327 sink-pdos:
328 description: An array of u32 with each entry providing supported power sink
331 Sink Capabilities Message, the order of each entry(PDO) should follow the
332 PD spec chapter 6.4.1. Required for power sink and power dual role. User
333 can specify the sink PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() defined
334 in dt-bindings/usb/pd.h.
337 $ref: /schemas/types.yaml#/definitions/uint32-array
339 op-sink-microwatt:
340 description: Sink required operating power in microwatt, if source can't
341 offer the power, Capability Mismatch is set. Required for power sink and
345 - $ref: "#/$defs/capabilities"
346 - if:
350 const: gpio-usb-b-connector
353 - required:
354 - vbus-gpios
355 - required:
356 - id-gpios
358 - if:
362 const: samsung,usb-connector-11pin
369 - not:
371 - typec-power-opmode
372 - new-source-frs-typec-current
377 # Micro-USB connector with HS lines routed via controller (MUIC).
378 - |
379 muic-max77843 {
381 compatible = "usb-b-connector";
382 label = "micro-USB";
387 # USB-C connector attached to CC controller (s2mm005), HS lines routed
390 - |
393 compatible = "usb-c-connector";
394 label = "USB-C";
404 #address-cells = <1>;
405 #size-cells = <0>;
410 remote-endpoint = <&max77865_usbc_hs>;
416 remote-endpoint = <&usbdrd_phy_ss>;
422 remote-endpoint = <&dp_aux>;
429 # USB-C connector attached to a typec port controller(ptn5110), which has
431 - |
432 #include <dt-bindings/usb/pd.h>
435 compatible = "usb-c-connector";
436 label = "USB-C";
437 power-role = "dual";
438 try-power-role = "sink";
439 source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>;
440 sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)
442 op-sink-microwatt = <10000000>;
443 sink-wait-cap-time-ms = <465>;
444 ps-source-off-time-ms = <835>;
445 cc-debounce-time-ms = <101>;
446 sink-bc12-completion-time-ms = <500>;
450 # USB-C connector attached to SoC with a single High-Speed controller
451 - |
453 compatible = "usb-c-connector";
454 label = "USB-C";
458 remote-endpoint = <&usb_hs_ep>;
463 # USB-C connector attached to SoC and USB3 typec port controller(hd3ss3220)
466 - |
468 compatible = "usb-c-connector";
469 label = "USB-C";
470 data-role = "dual";
473 #address-cells = <1>;
474 #size-cells = <0>;
478 remote-endpoint = <&usb3_hs_ep>;
484 remote-endpoint = <&hd3ss3220_in_ep>;
491 - |
492 #include <dt-bindings/gpio/gpio.h>
496 compatible = "gpio-usb-b-connector", "usb-b-connector";
498 id-gpios = <&pio 12 GPIO_ACTIVE_HIGH>;
499 vbus-supply = <&usb_p0_vbus>;
503 # Micro-USB connector with HS lines routed via controller (MUIC) and MHL
504 # lines connected to HDMI-MHL bridge (sii8620) on Samsung Exynos5433-based
506 - |
507 muic-max77843 {
509 compatible = "samsung,usb-connector-11pin", "usb-b-connector";
510 label = "micro-USB";
514 #address-cells = <1>;
515 #size-cells = <0>;
520 remote-endpoint = <&usb_to_muic>;
526 remote-endpoint = <&sii8620_mhl>;